timer_getoverrun(2) System Calls Manual timer_getoverrun(2)
NAME
timer_getoverrun - get overrun count for a POSIX per-process timer
LIBRARY
Real-time library (librt, -lrt)
SYNOPSIS
#include <time.h>
int timer_getoverrun(timer_t timerid);
Feature Test Macro Requirements for glibc (see feature_test_macros(7)):
timer_getoverrun():
_POSIX_C_SOURCE >= 199309L
DESCRIPTION
timer_getoverrun() returns the "overrun count" for the timer referred to
by timerid. An application can use the overrun count to accurately cal-
culate the number of timer expirations that would have occurred over a
given time interval. Timer overruns can occur both when receiving expi-
ration notifications via signals (SIGEV_SIGNAL), and via threads
(SIGEV_THREAD).
When expiration notifications are delivered via a signal, overruns can
occur as follows. Regardless of whether or not a real-time signal is
used for timer notifications, the system queues at most one signal per
timer. (This is the behavior specified by POSIX.1. The alternative,
queuing one signal for each timer expiration, could easily result in
overflowing the allowed limits for queued signals on the system.) Be-
cause of system scheduling delays, or because the signal may be tem-
porarily blocked, there can be a delay between the time when the notifi-
cation signal is generated and the time when it is delivered (e.g.,
caught by a signal handler) or accepted (e.g., using sigwaitinfo(2)).
In this interval, further timer expirations may occur. The timer over-
run count is the number of additional timer expirations that occurred
between the time when the signal was generated and when it was delivered
or accepted.
Timer overruns can also occur when expiration notifications are deliv-
ered via invocation of a thread, since there may be an arbitrary delay
between an expiration of the timer and the invocation of the notifica-
tion thread, and in that delay interval, additional timer expirations
may occur.
RETURN VALUE
On success, timer_getoverrun() returns the overrun count of the speci-
fied timer; this count may be 0 if no overruns have occurred. On fail-
ure, -1 is returned, and errno is set to indicate the error.
ERRORS
EINVAL timerid is not a valid timer ID.
VERSIONS
When timer notifications are delivered via signals (SIGEV_SIGNAL), on
Linux it is also possible to obtain the overrun count via the si_overrun
field of the siginfo_t structure (see sigaction(2)). This allows an ap-
plication to avoid the overhead of making a system call to obtain the
overrun count, but is a nonportable extension to POSIX.1.
POSIX.1 discusses timer overruns only in the context of timer notifica-
tions using signals.
STANDARDS
POSIX.1-2008.
HISTORY
Linux 2.6. POSIX.1-2001.
BUGS
POSIX.1 specifies that if the timer overrun count is equal to or greater
than an implementation-defined maximum, DELAYTIMER_MAX, then
timer_getoverrun() should return DELAYTIMER_MAX. However, before Linux
4.19, if the timer overrun value exceeds the maximum representable inte-
ger, the counter cycles, starting once more from low values. Since
Linux 4.19, timer_getoverrun() returns DELAYTIMER_MAX (defined as
INT_MAX in <limits.h>) in this case (and the overrun value is reset to
0).
EXAMPLES
See timer_create(2).
SEE ALSO
clock_gettime(2), sigaction(2), signalfd(2), sigwaitinfo(2), timer_cre-
ate(2), timer_delete(2), timer_settime(2), signal(7), time(7)
Linux man-pages 6.9.1 2024-05-02 timer_getoverrun(2)
Generated by dwww version 1.16 on Tue Dec 16 04:48:00 CET 2025.