SMARTCTL(8) SMART Monitoring Tools SMARTCTL(8)
NAME
smartctl - Control and Monitor Utility for SMART Disks
SYNOPSIS
smartctl [options] device
DESCRIPTION
[This man page is generated for the Linux version of smartmontools. It
does not contain info specific to other platforms.]
smartctl controls the Self-Monitoring, Analysis and Reporting Technology
(SMART) system built into most ATA/SATA and SCSI/SAS hard drives and
solid-state drives. The purpose of SMART is to monitor the reliability
of the hard drive and predict drive failures, and to carry out different
types of drive self-tests. smartctl also supports some features not re-
lated to SMART. This version of smartctl is compatible with ACS-3,
ACS-2, ATA8-ACS, ATA/ATAPI-7 and earlier standards (see REFERENCES be-
low).
smartctl also provides support for SCSI tape drives and changers (see
TAPE DRIVES below).
The user must specify the device to be controlled or interrogated as the
final argument to smartctl. The command set used by the device is often
derived from the device path but may need help with the '-d' option (for
more information see the section on "ATA, SCSI command sets and SAT" be-
low). Device paths are as follows:
LINUX: Use the forms "/dev/sd[a-z]" for ATA/SATA and SCSI/SAS devices.
For SCSI Tape Drives and Changers use the devices "/dev/nst*"
and "/dev/sg*". For disks behind 3ware controllers you may
need "/dev/sd[a-z]" or "/dev/twe[0-9]", "/dev/twa[0-9]" or
"/dev/twl[0-9]": see details below. For disks behind HighPoint
RocketRAID controllers you may need "/dev/sd[a-z]". For disks
behind Areca SATA RAID controllers, you need "/dev/sg[2-9]"
(note that smartmontools interacts with the Areca controllers
via a SCSI generic device which is different than the SCSI de-
vice used for reading and writing data)! For HP Smart Array
RAID controllers, there are three currently supported drivers:
cciss, hpsa, and hpahcisr. For disks accessed via the cciss
driver the device nodes are of the form "/dev/cciss/c[0-9]d0".
For disks accessed via the hpahcisr and hpsa drivers, the de-
vice nodes you need are "/dev/sg[0-9]*". ("lsscsi -g" is help-
ful in determining which scsi generic device node corresponds
to which device.) Use the nodes corresponding to the RAID con-
trollers, not the nodes corresponding to logical drives. See
the -d option below, as well. Use the forms "/dev/nvme[0-9]"
(broadcast namespace) or "/dev/nvme[0-9]n[1-9]" (specific name-
space 1-9) for NVMe devices.
if '-' is specified as the device path, smartctl reads and interprets
it's own debug output from standard input. See '-r ataioctl' below for
details.
smartctl guesses the device type if possible. If necessary, the '-d'
option can be used to override this guess.
Note that the printed output of smartctl displays most numerical values
in base 10 (decimal), but some values are displayed in base 16 (hexadec-
imal). To distinguish them, the base 16 values are always displayed
with a leading "0x", for example: "0xff". This man page follows the
same convention.
OPTIONS
The options are grouped below into several categories. smartctl will
execute the corresponding commands in the order: INFORMATION, EN-
ABLE/DISABLE, DISPLAY DATA, RUN/ABORT TESTS.
SHOW INFORMATION OPTIONS:
-h, --help, --usage
Prints a usage message to STDOUT and exits.
-V, --version, --copyright, --license
Prints version, copyright, license, home page and SVN revision
information for your copy of smartctl to STDOUT and then exits.
-i, --info
Prints the device model number, serial number, firmware version,
and ATA Standard version/revision information. Says if the de-
vice supports SMART, and if so, whether SMART support is cur-
rently enabled or disabled. If the device supports Logical Block
Address mode (LBA mode) print current user drive capacity in
bytes. (If drive has a user protected area reserved, or is
"clipped", this may be smaller than the potential maximum drive
capacity.) Indicates if the drive is in the smartmontools data-
base (see '-v' options below). If so, the drive model family may
also be printed. If '-n' (see below) is specified, the power
mode of the drive is printed.
[NVMe] For NVMe devices the information is obtained from the
Identify Controller and the Identify Namespace data structure.
--identify[=[w][nvb]]
[ATA only] Prints an annotated table of the IDENTIFY DEVICE data.
By default, only valid words (words not equal to 0x0000 or
0xffff) and nonzero bits and bit fields are printed. This can be
changed by the optional argument which consists of one or two
characters from the set 'wnvb'. The character 'w' enables print-
ing of all 256 words. The character 'n' suppresses printing of
bits, 'v' enables printing of all bits from valid words, 'b' en-
ables printing of all bits. For example '--identify=n' (valid
words, no bits) produces the shortest output and '--identify=wb'
(all words, all bits) produces the longest output.
-a, --all
Prints all SMART information about the device.
For ATA, this is equivalent to
'-H -i -c -A -l error -l selftest -l selective'.
This option is no longer recommended for ATA disks because it
does not enable the SMART options which require support for
48-bit ATA commands (see '-x' below).
For SCSI, this is equivalent to
'-H -i -A -l error -l selftest'.
For NVMe, this is equivalent to
'-H -i -c -A -l error -l selftest'.
-x, --xall
Prints all SMART and non-SMART information about the device.
For ATA, this is equivalent to
'-H -i -g all -g wcreorder -c -A -f brief -l xerror,error -l
xselftest,selftest -l selective -l directory -l scttemp -l scterc
-l devstat -l defects -l sataphy'.
If '-a' is also specified, add '-l error -l selftest'.
For SCSI disks, this is equivalent to
'-H -i -g all -A -l error -l selftest -l background -l sasphy -l
defects -l envrep -l genstats -l ssd -l zdevstat'
and for SCSI tape drives and changers, add '-l tapedevstat'.
For NVMe, this is equivalent to
'-H -i -c -A -l error -l selftest'.
--scan Scans for devices and prints each device name, device type and
protocol ([ATA] or [SCSI]) info. May be used in conjunction with
'-d TYPE' to restrict the scan to a specific TYPE. See also info
about platform specific device scan and the DEVICESCAN directive
on smartd(8) man page.
--scan-open
Same as --scan, but also tries to open each device before print-
ing device info. The device open may change the device type due
to autodetection (see also '-d test').
This option can be used to create a draft smartd.conf file. All
options after '--' are appended to each output line. For exam-
ple:
smartctl --scan-open -- -a -W 4,45,50 -m admin@work > smartd.conf
Multiple '-d TYPE' options may be specified with '--scan[-open]'
to combine the scan results of more than one TYPE.
-g NAME, --get=NAME
Get non-SMART device settings. See '-s, --set' below for further
info.
RUN-TIME BEHAVIOR OPTIONS:
-j, --json[=cgiosuvy]
Enables JSON or YAML output mode.
The output could be modified or enhanced by the optional argument
which consists of one or more characters from the set 'cgiosuvy':
'c': Outputs compact format without extra spaces and newlines.
By default, output is pretty-printed. If used with YAML format,
the indentation of arrays is reduced.
'g': Outputs JSON structure as single assignments to allow the
usage of grep. Each assignment reflects the absolute path of a
value. The syntax is compatible with gron:
'json.KEY1[INDEX2].KEY3 = VALUE;'.
'o': Includes the full original plaintext output of smartctl as a
JSON array 'smartctl.output[]'.
's': Outputs JSON object elements sorted by key. By default, ob-
ject elements are ordered as generated internally.
'v': Enables verbose output of possible unsafe integers. If
specified, values which may exceed JSON safe integer (53-bit)
range are always output as a number (with some 'KEY') and a
string ('KEY_s'), regardless of the actual value. Values which
may exceed 64-bit range are also output as a little endian byte
array ('KEY_le'). By default, the additional elements are only
output if the value actually exceeds the range.
'y': Outputs in YAML format.
The following two arguments are primarily intended for develop-
ment:
'i': Includes lines from the plaintext output which print info
already implemented for JSON output. The lines appear as strings
with key 'smartctl_NNNN_i'.
'u': Includes lines from the plaintext output which print info
still unimplemented for JSON output. The lines appear as strings
with key 'smartctl_NNNN_u'.
-q TYPE, --quietmode=TYPE
Specifies that smartctl should run in one of the quiet modes de-
scribed here. The valid arguments to this option are:
errorsonly - only print: For the '-l error' option, if nonzero,
the number of errors recorded in the SMART error log and the
power-on time when they occurred; For the '-l selftest' option,
errors recorded in the device self-test log; For the '-H' option,
SMART "disk failing" status or device Attributes (pre-failure or
usage) which failed either now or in the past; For the '-A' op-
tion, device Attributes (pre-failure or usage) which failed ei-
ther now or in the past.
silent - print no output. The only way to learn about what was
found is to use the exit status of smartctl (see EXIT STATUS be-
low).
noserial - Do not print the serial number of the device. This
also suppresses the LU WWN Device Id (ATA) and the SAS addresses
(SCSI). The related fields are also invalidated in the ATA and
NVMe debug outputs.
Note: This is not the case in SCSI debug output.
[NEW EXPERIMENTAL SMARTCTL 7.4 FEATURE] The Namespace IEEE EUI-64
(NVMe) is also suppressed.
-d TYPE, --device=TYPE
Specifies the type of the device. The valid arguments to this
option are:
auto - attempt to guess the device type from the device name or
from controller type info provided by the operating system or
from a matching USB ID entry in the drive database. This is the
default.
test - prints the guessed TYPE, then opens the device and prints
the (possibly changed) TYPE name and then exits without perform-
ing any further commands.
ata - the device type is ATA. This prevents smartctl from issu-
ing SCSI commands to an ATA device.
scsi - the device type is SCSI. This prevents smartctl from is-
suing ATA commands to a SCSI device.
nvme[,NSID] - the device type is NVM Express (NVMe). The op-
tional parameter NSID specifies the namespace id (in hex) passed
to the driver. Use 0xffffffff for the broadcast namespace id.
The default for NSID is the namespace id addressed by the device
name.
sat[,auto][,N] - the device type is SCSI to ATA Translation
(SAT). This is for ATA disks that have a SCSI to ATA Translation
Layer (SATL) between the disk and the operating system. SAT de-
fines two ATA PASS THROUGH SCSI commands, one 12 bytes long and
the other 16 bytes long. The default is the 16 byte variant
which can be overridden with either '-d sat,12' or '-d sat,16'.
If '-d sat,auto' is specified, device type SAT (for ATA/SATA
disks) is only used if the SCSI INQUIRY data reports a SATL (VEN-
DOR: "ATA "). Otherwise device type SCSI (for SCSI/SAS
disks) is used.
usbasm1352r,PORT - [NEW EXPERIMENTAL SMARTCTL 7.4 FEATURE] this
device type is for one or two SATA disks that are behind an ASMe-
dia ASM1352R USB to SATA (RAID) bridge. The parameter PORT (0 or
1) selects the disk to monitor.
Note: This USB bridge also supports '-d sat'. This monitors ei-
ther the first disk or the second disk if no disk is connected to
the first port.
usbcypress - this device type is for ATA disks that are behind a
Cypress USB to PATA bridge. This will use the ATACB proprietary
scsi pass through command. The default SCSI operation code is
0x24, but although it can be overridden with '-d usbcypress,0xN',
where N is the scsi operation code, you're running the risk of
damage to the device or filesystems on it.
usbjmicron[,p][,x][,PORT] - this device type is for SATA disks
that are behind a JMicron USB to PATA/SATA bridge. The 48-bit
ATA commands (required e.g. for '-l xerror', see below) do not
work with all of these bridges and are therefore disabled by de-
fault. These commands can be enabled by '-d usbjmicron,x'. If
two disks are connected to a bridge with two ports, an error mes-
sage is printed if no PORT (0 or 1) is specified.
The PORT parameter is not necessary if the device uses a port
multiplier to connect multiple disks to one port. The disks ap-
pear under separate /dev/ice names then.
CAUTION: Specifying ',x' for a device which does not support it
results in I/O errors and may disconnect the drive. The same ap-
plies if the specified PORT does not exist or is not connected to
a disk.
The Prolific PL2507/3507 USB bridges with older firmware support
a pass-through command similar to JMicron and work with '-d usb-
jmicron,0'. Newer Prolific firmware requires a modified command
which can be selected by '-d usbjmicron,p'. Note that this does
not yet support the SMART status command.
usbprolific - this device type is for SATA disks that are behind
a Prolific PL2571/2771/2773/2775 USB to SATA bridge.
usbsunplus - this device type is for SATA disks that are behind a
SunplusIT USB to SATA bridge.
sntasmedia - [NEW EXPERIMENTAL SMARTCTL 7.3 FEATURE] this device
type is for NVMe disks that are behind an ASMedia USB to NVMe
bridge.
sntjmicron[,NSID] - this device type is for NVMe disks that are
behind a JMicron USB to NVMe bridge. The optional parameter NSID
specifies the namespace id (in hex) passed to the driver. The
default namespace id is the broadcast namespace id (0xffffffff).
sntrealtek - this device type is for NVMe disks that are behind a
Realtek USB to NVMe bridge.
marvell - [Linux only] (deprecated and subject to remove).
megaraid,N - [FreeBSD and Linux only] the device consists of one
or more SCSI/SAS disks connected to a MegaRAID controller. The
non-negative integer N (in the range of 0 to 127 inclusive) de-
notes which disk on the controller is monitored. This interface
will also work for Dell PERC controllers. Use syntax such as:
smartctl -a -d megaraid,2 /dev/sda
smartctl -a -d megaraid,0 /dev/sdb
smartctl -a -d megaraid,0 /dev/bus/0
It is possible to set RAID device name as /dev/bus/N, where N is
a SCSI bus number.
The following entry in /proc/devices must exist:
For PERC2/3/4 controllers: megadevN
For PERC5/6 controllers: megaraid_sas_ioctlN
aacraid,H,L,ID - [Linux, Windows and Cygwin only] the device con-
sists of one or more SCSI/SAS or SATA disks connected to an
AacRaid controller. The non-negative integers H,L,ID (Host num-
ber, Lun, ID) denote which disk on the controller is monitored.
Use syntax such as:
smartctl -a -d aacraid,0,0,2 /dev/sda
smartctl -a -d aacraid,1,0,4 /dev/sdb
Option '-d sat,auto+...' is implicitly enabled to detect SATA
disks. Use '-d scsi+aacraid,H,L,ID' to disable it.
On Linux, the following entry in /proc/devices must exist: aac.
Character device nodes /dev/aacH (H=Host number) are created if
required.
3ware,N - [FreeBSD and Linux only] the device consists of one or
more ATA disks connected to a 3ware RAID controller. The non-
negative integer N (in the range from 0 to 127 inclusive) denotes
which disk on the controller is monitored. Use syntax such as:
smartctl -a -d 3ware,2 /dev/sda [Linux only]
smartctl -a -d 3ware,0 /dev/twe0
smartctl -a -d 3ware,1 /dev/twa0
smartctl -a -d 3ware,1 /dev/twl0 [Linux only]
smartctl -a -d 3ware,1 /dev/tws0 [FreeBSD only]
The first two forms, which refer to devices /dev/sda-z (depre-
cated) and /dev/twe0-15, may be used with 3ware series 6000,
7000, and 8000 series controllers that use the 3x-xxxx driver.
The devices /dev/twa0-15, must be used with 3ware 9000 series
controllers, which use the 3w-9xxx driver. The devices
/dev/twl0-15 [Linux] or /dev/tws0-15 [FreeBSD] must be used with
the 3ware/LSI 9750 series controllers which use the 3w-sas dri-
ver.
Note that if the special character device nodes /dev/tw[ls]?,
/dev/twa? and /dev/twe? do not exist, or exist with the incor-
rect major or minor numbers, smartctl will recreate them on the
fly.
areca,N - [FreeBSD, Linux, Windows and Cygwin only] the device
consists of one or more SATA disks connected to an Areca SATA
RAID controller. The positive integer N (in the range from 1 to
24 inclusive) denotes which disk on the controller is monitored.
On Linux use syntax such as:
smartctl -a -d areca,2 /dev/sg2
smartctl -a -d areca,3 /dev/sg3
The first line above addresses the second disk on the first Areca
RAID controller. The second line addresses the third disk on the
second Areca RAID controller. To help identify the correct de-
vice on Linux, use the command:
cat /proc/scsi/sg/device_hdr /proc/scsi/sg/devices
to show the SCSI generic devices (one per line, starting with
/dev/sg0). The correct SCSI generic devices to address for
smartmontools are the ones with the type field equal to 3. If
the incorrect device is addressed, please read the warning/error
messages carefully. They should provide hints about what devices
to use.
Important: the Areca controller must have firmware version 1.46
or later. Lower-numbered firmware versions will give (harmless)
SCSI error messages and no SMART information.
areca,N/E - [FreeBSD, Linux, Windows and Cygwin only] the device
consists of one or more SATA or SAS disks connected to an Areca
SAS RAID controller. The integer N (range 1 to 128) denotes the
channel (slot) and E (range 1 to 8) denotes the enclosure. Im-
portant: This requires Areca SAS controller firmware version 1.51
or later.
cciss,N - [FreeBSD and Linux only] the device consists of one or
more SCSI/SAS or SATA disks connected to a cciss RAID controller.
The non-negative integer N (in the range from 0 to 15 inclusive)
denotes which disk on the controller is monitored.
Option '-d sat,auto+...' is implicitly enabled to detect SATA
disks. Use '-d scsi+cciss,N' to disable it.
To look at disks behind HP Smart Array controllers, use syntax
such as:
smartctl -a -d cciss,0 /dev/cciss/c0d0 (cciss driver under
Linux)
smartctl -a -d cciss,0 /dev/sg2 (hpsa or hpahcisr drivers un-
der Linux)
hpt,L/M/N - [FreeBSD and Linux only] the device consists of one
or more ATA disks connected to a HighPoint RocketRAID controller.
The integer L is the controller id, the integer M is the channel
number, and the integer N is the PMPort number if it is avail-
able. The allowed values of L are from 1 to 4 inclusive, M are
from 1 to 128 inclusive and N from 1 to 4 if PMPort available.
And also these values are limited by the model of the HighPoint
RocketRAID controller. Use syntax such as:
smartctl -a -d hpt,1/3 /dev/sda (under Linux)
smartctl -a -d hpt,1/2/3 /dev/sda (under Linux)
Note that the /dev/sda-z form should be the device node which
stands for the disks derived from the HighPoint RocketRAID con-
trollers under Linux and under FreeBSD, it is the character de-
vice which the driver registered (eg, /dev/hptrr, /dev/hptmv6).
sssraid,E,S - [Linux only: NEW EXPERIMENTAL SMARTCTL 7.4 FEATURE]
the device consists of one or more SCSI/SAS or SATA disks con-
nected to a SSSRAID controller. The non-negative integer E (in
the range of 0 to 8) denotes the enclosure and S (range 0 to 128)
denotes the slot. Use syntax such as:
smartctl -a -d sssraid,0,1 /dev/bsg/sssraid0
It is possible to set RAID device name as /dev/bsg/sssraidN,
where N is a SCSI bus number.
intelliprop,N[+TYPE] - (deprecated and subject to remove).
jmb39x[-q],N[,sLBA][,force][+TYPE] - the device consists of mul-
tiple SATA disks connected to a JMicron JMB39x RAID port multi-
plier. The suffix '-q' selects a slightly different command
variant used by some QNAP NAS devices. The integer N is the port
number from 0 to 4.
WARNING: The ATA pass-through commands are issued via READ/WRITE
commands to a LBA of the RAID volume. Using this option with
other devices may overwrite this sector.
The default LBA is 33. The LBA could be selected in the range
from 1 to 255 inclusive.
If a GPT partition table is used, LBA 33 contains the last 4 (of
128) entries of the partition table. These entries are zero
filled in most cases. If a MBR partition table is used, LBA 33
may be zero filled or may contain code from a boot loader.
By default, access to the device is refused if the selected sec-
tor is not zero filled. The 'force' flag disables this check.
WARNING: Original sector data is not written back if smartctl is
aborted with a signal.
jms56x,N[,sLBA][,force][+TYPE] - the device consists of multiple
SATA disks connected to a JMicron JMS56x USB to SATA RAID bridge.
See 'jmb39x...' above for valid arguments.
-T TYPE, --tolerance=TYPE
[ATA only] Specifies how tolerant smartctl should be of ATA and
SMART command failures.
The behavior of smartctl depends upon whether the command is "op-
tional" or "mandatory". Here "mandatory" means "required by the
ATA Specification if the device implements the SMART command set"
and "optional" means "not required by the ATA Specification even
if the device implements the SMART command set." The "mandatory"
ATA and SMART commands are: (1) ATA IDENTIFY DEVICE, (2) SMART
ENABLE/DISABLE ATTRIBUTE AUTOSAVE, (3) SMART ENABLE/DISABLE, and
(4) SMART RETURN STATUS.
The valid arguments to this option are:
normal - exit on failure of any mandatory SMART command, and ig-
nore all failures of optional SMART commands. This is the de-
fault. Note that on some devices, issuing unimplemented optional
SMART commands doesn't cause an error. This can result in mis-
leading smartctl messages such as "Feature X not implemented",
followed shortly by "Feature X: enabled". In most such cases,
contrary to the final message, Feature X is not enabled.
conservative - exit on failure of any optional SMART command.
permissive - ignore failure(s) of mandatory SMART commands. This
option may be given more than once. Each additional use of this
option will cause one more additional failure to be ignored.
Note that the use of this option can lead to messages like "Fea-
ture X not supported", followed shortly by "Feature X enable
failed". In a few such cases, contrary to the final message,
Feature X is enabled.
verypermissive - equivalent to giving a large number of '-T per-
missive' options: ignore failures of any number of mandatory
SMART commands. Please see the note above.
-b TYPE, --badsum=TYPE
[ATA only] Specifies the action smartctl should take if a check-
sum error is detected in the: (1) Device Identity Structure, (2)
SMART Self-Test Log Structure, (3) SMART Attribute Value Struc-
ture, (4) SMART Attribute Threshold Structure, or (5) ATA Error
Log Structure.
The valid arguments to this option are:
warn - report the incorrect checksum but carry on in spite of it.
This is the default.
exit - exit smartctl.
ignore - continue silently without issuing a warning.
-r TYPE, --report=TYPE
Intended primarily to help smartmontools developers understand
the behavior of smartmontools on non-conforming or poorly con-
forming hardware. This option reports details of smartctl trans-
actions with the device. The option can be used multiple times.
When used just once, it shows a record of the ioctl() transac-
tions with the device. When used more than once, the detail of
these ioctl() transactions are reported in greater detail. The
valid arguments to this option are:
ioctl - report all ioctl() transactions.
ataioctl - report only ioctl() transactions with ATA devices.
scsiioctl - report only ioctl() transactions with SCSI devices.
Invoking this once shows the SCSI commands in hex and the corre-
sponding status. Invoking it a second time adds a hex listing of
the first 64 bytes of data send to, or received from the device.
nvmeioctl - report only ioctl() transactions with NVMe devices.
Any argument may include a positive integer to specify the level
of detail that should be reported. The argument should be fol-
lowed by a comma then the integer with no spaces. For example,
ataioctl,2 The default level is 1, so '-r ataioctl,1' and '-r
ataioctl' are equivalent.
For testing purposes, the output of '-r ataioctl,2' can later be
parsed by smartctl itself if '-' is used as device path argument.
The ATA command input parameters, sector data and return values
are reconstructed from the debug report read from stdin. Then
smartctl internally simulates an ATA device with the same behav-
iour. This is does not work for SCSI devices yet.
-n POWERMODE[,STATUS[,STATUS2]], --nocheck=POWERMODE[,STATUS[,STATUS2]]
[ATA, SCSI] Specifies if smartctl should exit before performing
any checks when the device is in a low-power mode. It may be
used to prevent a disk from being spun-up by smartctl. The power
mode is ignored by default.
Note: If this option is used it may also be necessary to specify
the device type with the '-d' option. Otherwise the device may
spin up due to commands issued during device type autodetection.
By default, exit status 2 is returned if the device is in one of
the specified low-power modes. This status is also returned if
the device open or identification failed (see EXIT STATUS below).
The optional STATUS parameter allows one to override this de-
fault. STATUS is an integer in the range from 0 to 255 inclu-
sive. For example use '-n standby,0' to return success if a de-
vice is in SLEEP or STANDBY mode. Use '-n standby,3' to return a
unique exit status in this case.
The valid arguments to this option are:
never - check the device always, but print the power mode if '-i'
is specified.
sleep[,STATUS[,STATUS2]] - check the device unless it is in SLEEP
mode.
standby[,STATUS[,STATUS2]] - check the device unless it is in
SLEEP or STANDBY mode. In these modes most disks are not spin-
ning, so if you want to prevent a disk from spinning up, this is
probably what you want.
idle[,STATUS[,STATUS2]] - check the device unless it is in SLEEP,
STANDBY or IDLE mode. In the IDLE state, most disks are still
spinning, so this is probably not what you want.
The '-n' option is ignored if the power mode check is not sup-
ported or returns an unknown value.
[ATA only: NEW EXPERIMENTAL SMARTCTL 7.3 FEATURE] If the optional
STATUS2 parameter is specified, smartctl exits immediately with
STATUS2 in this case. For example use '-n standby,3,5' to return
unique exit statuses in the STANDBY and UNSUPPORTED cases.
SMART FEATURE ENABLE/DISABLE COMMANDS:
Note: if multiple options are used to both enable and disable a
feature, then both the enable and disable commands will be is-
sued. The enable command will always be issued before the corre-
sponding disable command.
-s VALUE, --smart=VALUE
Enables or disables SMART on device. The valid arguments to this
option are on and off.
[ATA] Note that the ATA commands SMART ENABLE/DISABLE OPERATIONS
were declared obsolete in ATA ACS-4 Revision 10 (Nov 2015).
[SCSI tape drive or changer] It is not necessary (or useful) to
enable SMART to see the TapeAlert messages.
-o VALUE, --offlineauto=VALUE
[ATA only] Enables or disables SMART automatic offline test,
which scans the drive every four hours for disk defects. This
command can be given during normal system operation. The valid
arguments to this option are on and off.
Note that the SMART automatic offline test command is listed as
"Obsolete" in every version of the ATA and ATA/ATAPI Specifica-
tions. It was originally part of the SFF-8035i Revision 2.0
specification, but was never part of any ATA specification. How-
ever it is implemented and used by many vendors. You can tell if
automatic offline testing is supported by seeing if this command
enables and disables it, as indicated by the 'Auto Offline Data
Collection' part of the SMART capabilities report (displayed with
'-c').
SMART provides three basic categories of testing. The first cat-
egory, called "online" testing, has no effect on the performance
of the device. It is turned on by the '-s on' option.
The second category of testing is called "offline" testing. This
type of test can, in principle, degrade the device performance.
The '-o on' option causes this offline testing to be carried out,
automatically, on a regular scheduled basis. Normally, the disk
will suspend offline testing while disk accesses are taking
place, and then automatically resume it when the disk would oth-
erwise be idle, so in practice it has little effect. Note that a
one-time offline test can also be carried out immediately upon
receipt of a user command. See the '-t offline' option below,
which causes a one-time offline test to be carried out immedi-
ately.
The choice (made by the SFF-8035i and ATA specification authors)
of the word testing for these first two categories is unfortu-
nate, and often leads to confusion. In fact these first two cat-
egories of online and offline testing could have been more accu-
rately described as online and offline data collection.
The results of this automatic or immediate offline testing (data
collection) are reflected in the values of the SMART Attributes.
Thus, if problems or errors are detected, the values of these At-
tributes will go below their failure thresholds; some types of
errors may also appear in the SMART error log. These are visible
with the '-A' and '-l error' options respectively.
Some SMART attribute values are updated only during off-line data
collection activities; the rest are updated during normal opera-
tion of the device or during both normal operation and off-line
testing. The Attribute value table produced by the '-A' option
indicates this in the UPDATED column. Attributes of the first
type are labeled "Offline" and Attributes of the second type are
labeled "Always".
The third category of testing (and the only category for which
the word 'testing' is really an appropriate choice) is "self"
testing. This third type of test is only performed (immediately)
when a command to run it is issued. The '-t' and '-X' options
can be used to carry out and abort such self-tests; please see
below for further details.
Any errors detected in the self testing will be shown in the
SMART self-test log, which can be examined using the '-l self-
test' option.
Note: in this manual page, the word "Test" is used in connection
with the second category just described, e.g. for the "offline"
testing. The words "Self-test" are used in connection with the
third category.
-S VALUE, --saveauto=VALUE
[ATA] Enables or disables SMART autosave of device vendor-spe-
cific Attributes. The valid arguments to this option are on and
off. Note that this feature is preserved across disk power cy-
cles, so you should only need to issue it once.
The ATA standard does not specify a method to check whether SMART
autosave is enabled. Unlike SCSI (below), smartctl is unable to
print a warning if autosave is disabled.
Note that the ATA commands SMART ENABLE/DISABLE AUTOSAVE were de-
clared obsolete in ATA ACS-4 Revision 10 (Nov 2015).
[SCSI] For SCSI devices this toggles the value of the Global Log-
ging Target Save Disabled (GLTSD) bit in the Control Mode Page.
Some disk manufacturers set this bit by default. This prevents
error counters, power-up hours and other useful data from being
placed in non-volatile storage, so these values may be reset to
zero the next time the device is power-cycled. If the GLTSD bit
is set then 'smartctl -a' will issue a warning. Use on to clear
the GLTSD bit and thus enable saving counters to non-volatile
storage. For extreme streaming-video type applications you might
consider using off to set the GLTSD bit.
-g NAME, --get=NAME, -s NAME[,VALUE], --set=NAME[,VALUE]
Gets/sets non-SMART device settings. Note that the '--set' op-
tion shares its short option '-s' with '--smart'. Valid argu-
ments are:
all - Gets all values. This is equivalent to
'-g aam -g apm -g lookahead -g security -g wcache -g rcache -g
dsn'
aam[,N|off] - [ATA only] Gets/sets the Automatic Acoustic Manage-
ment (AAM) feature (if supported). A value of 128 sets the most
quiet (slowest) mode and 254 the fastest (loudest) mode, 'off'
disables AAM. Devices may support intermediate levels. Values
below 128 are defined as vendor specific (0) or retired (1 to
127). Note that the AAM feature was declared obsolete in ATA
ACS-2 Revision 4a (Dec 2010).
apm[,N|off] - [ATA only] Gets/sets the Advanced Power Management
(APM) feature on device (if supported). If a value between 1 and
254 is provided, it will attempt to enable APM and set the speci-
fied value, 'off' disables APM. Note the actual behavior depends
on the drive, for example some drives disable APM if their value
is set above 128. Values below 128 are supposed to allow drive
spindown, values 128 and above adjust only head-parking fre-
quency, although the actual behavior defined is also vendor-spe-
cific.
lookahead[,on|off] - [ATA only] Gets/sets the read look-ahead
feature (if supported). Read look-ahead is usually enabled by
default.
security - [ATA only] Gets the status of ATA Security feature (if
supported). If ATA Security is enabled an ATA user password is
set. The drive will be locked on next reset then.
security-freeze - [ATA only] Sets ATA Security feature to frozen
mode. This prevents that the drive accepts any security commands
until next reset. Note that the frozen mode may already be set
by BIOS or OS.
standby,[N|off] - [ATA] Sets the standby (spindown) timer and
places the drive in the IDLE mode. A value of 0 or 'off' dis-
ables the standby timer. Values from 1 to 240 specify timeouts
from 5 seconds to 20 minutes in 5 second increments. Values from
241 to 251 specify timeouts from 30 minutes to 330 minutes in 30
minute increments. Value 252 specifies 21 minutes. Value 253
specifies a vendor specific time between 8 and 12 hours. Value
255 specifies 21 minutes and 15 seconds. Some drives may use a
vendor specific interpretation for the values. Note that there
is no get option because ATA standards do not specify a method to
read the standby timer. If '-s standby,now' is also specified,
the drive is immediately placed in the STANDBY mode without tem-
porarily placing it in the IDLE mode. Note that ATA standards do
not specify a command to set the standby timer without affecting
the power mode.
[SCSI] Only the set option with 'standby,off' or 'standby,0' is
accepted and will place the SCSI disk into "ACTIVE" power condi-
tion.
standby,now - [ATA] Places the drive in the STANDBY mode. This
usually spins down the drive. The setting of the standby timer
is not affected unless '-s standby,[N|off]' is also specified.
[SCSI] Only the set option is accepted and will place the SCSI
disk into "STANDBY_Z" power condition.
wcache[,on|off] - [ATA] Gets/sets the volatile write cache fea-
ture (if supported). The write cache is usually enabled by de-
fault.
wcache[,on|off] - [SCSI] Gets/sets the 'Write Cache Enable' (WCE)
bit (if supported). The write cache is usually enabled by de-
fault.
wcache-sct[,ata|on|off[,p]] - [ATA only] Gets/sets the write
cache feature through SCT Feature Control (if supported). The
state of write cache in SCT Feature Control could be "Controlled
by ATA", "Force Enabled", or "Force Disabled". SCT Feature con-
trol overwrites the setting by ATA Set Features command
(wcache[,on|off] option). If SCT Feature Control sets write
cache as "Force Enabled" or "Force Disabled", the setting of
wcache[,on|off] is ignored by the drive. SCT Feature Control
usually sets write cache as "Controlled by ATA" by default. If
',p' is specified, the setting is preserved across power cycles.
wcreorder[,on|off[,p]] - [ATA only] Gets/sets Write Cache Re-
ordering. If it is disabled (off), disk write scheduling is exe-
cuted on a first-in-first-out (FIFO) basis. If Write Cache Re-
ordering is enabled (on), then disk write scheduling may be re-
ordered by the drive. If write cache is disabled, the current
Write Cache Reordering state is remembered but has no effect on
non-cached writes, which are always written in the order re-
ceived. The state of Write Cache Reordering has no effect on ei-
ther NCQ or LCQ queued commands. If ',p' is specified, the set-
ting is preserved across power cycles.
rcache[,on|off] - [SCSI only] Gets/sets the 'Read Cache Disable'
(RCE) bit. 'Off' value disables read cache (if supported). The
read cache is usually enabled by default.
dsn[,on|off] - [ATA only] Gets/sets the DSN feature (if sup-
ported). The dsn is usually disabled by default.
SMART READ AND DISPLAY DATA OPTIONS:
-H, --health
Prints the health status of the device.
If the device reports failing health status, this means either
that the device has already failed, or that it is predicting its
own failure within the next 24 hours. If this happens, use the
'-x' option to get more information, and get your data off the
disk and to someplace safe as soon as you can.
[ATA] Health status is obtained by checking the (boolean) result
returned by the SMART RETURN STATUS command. The return value of
this ATA command may be unknown due to limitations or bugs in
some layer (e.g. RAID controller or USB bridge firmware) between
disk and operating system. In this case, smartctl prints a warn-
ing and checks whether any Prefailure SMART Attribute value is
less than or equal to its threshold (see '-A' below).
[SCSI] Health status is obtained by checking the Additional Sense
Code (ASC) and Additional Sense Code Qualifier (ASCQ) from Infor-
mal Exceptions (IE) log page (if supported) and/or from SCSI
sense data.
[SCSI tape drive or changer] The TapeAlert status is obtained by
reading the TapeAlert log page, but only if this option is given
twice (see TAPE DRIVES for the rationale).
[NVMe] NVMe status is obtained by reading the "Critical Warning"
byte from the SMART/Health Information log.
-c, --capabilities
[ATA] Prints only the generic SMART capabilities. These show
what SMART features are implemented and how the device will re-
spond to some of the different SMART commands. For example it
shows if the device logs errors, if it supports offline surface
scanning, and so on. If the device can carry out self-tests,
this option also shows the estimated time required to run those
tests.
[NVMe] Prints various NVMe device capabilities obtained from the
Identify Controller and the Identify Namespace data structure.
-A, --attributes
[ATA] Prints only the vendor specific SMART Attributes. The At-
tributes are numbered from 1 to 253 and have specific names and
ID numbers. For example Attribute 12 is "power cycle count": how
many times has the disk been powered up.
Each Attribute has a "Raw" value, printed under the heading
"RAW_VALUE", and a "Normalized" value printed under the heading
"VALUE". [Note: smartctl prints these values in base-10.] In
the example just given, the "Raw Value" for Attribute 12 would be
the actual number of times that the disk has been power-cycled,
for example 365 if the disk has been turned on once per day for
exactly one year. Each vendor uses their own algorithm to con-
vert this "Raw" value to a "Normalized" value in the range from 1
to 254. Please keep in mind that smartctl only reports the dif-
ferent Attribute types, values, and thresholds as read from the
device. It does not carry out the conversion between "Raw" and
"Normalized" values: this is done by the disk's firmware.
The conversion from Raw value to a quantity with physical units
is not specified by the SMART standard. In most cases, the val-
ues printed by smartctl are sensible. For example the tempera-
ture Attribute generally has its raw value equal to the tempera-
ture in Celsius. However in some cases vendors use unusual con-
ventions. For example the Hitachi disk on my laptop reports its
power-on hours in minutes, not hours. Some IBM disks track three
temperatures rather than one, in their raw values. And so on.
Each Attribute also has a Threshold value (whose range is 0 to
255) which is printed under the heading "THRESH". If the Normal-
ized value is less than or equal to the Threshold value, then the
Attribute is said to have failed. If the Attribute is a pre-
failure Attribute, then disk failure is imminent.
Each Attribute also has a "Worst" value shown under the heading
"WORST". This is the smallest (closest to failure) value that
the disk has recorded at any time during its lifetime when SMART
was enabled. [Note however that some vendors firmware may actu-
ally increase the "Worst" value for some "rate-type" Attributes.]
The Attribute table printed out by smartctl also shows the "TYPE"
of the Attribute. Attributes are one of two possible types: Pre-
failure or Old age. Pre-failure Attributes are ones which, if
less than or equal to their threshold values, indicate pending
disk failure. Old age, or usage Attributes, are ones which indi-
cate end-of-product life from old-age or normal aging and
wearout, if the Attribute value is less than or equal to the
threshold. Please note: the fact that an Attribute is of type
'Pre-fail' does not mean that your disk is about to fail! It
only has this meaning if the Attribute's current Normalized value
is less than or equal to the threshold value.
If the Attribute's current Normalized value is less than or equal
to the threshold value, then the "WHEN_FAILED" column will dis-
play "FAILING_NOW". If not, but the worst recorded value is less
than or equal to the threshold value, then this column will dis-
play "In_the_past". If the "WHEN_FAILED" column has no entry
(indicated by a dash: '-') then this Attribute is OK now (not
failing) and has also never failed in the past.
The table column labeled "UPDATED" shows if the SMART Attribute
values are updated during both normal operation and off-line
testing, or only during offline testing. The former are labeled
"Always" and the latter are labeled "Offline".
So to summarize: the Raw Attribute values are the ones that might
have a real physical interpretation, such as "Temperature Cel-
sius", "Hours", or "Start-Stop Cycles". Each manufacturer con-
verts these, using their detailed knowledge of the disk's opera-
tions and failure modes, to Normalized Attribute values in the
range 1–254. The current and worst (lowest measured) of these
Normalized Attribute values are stored on the disk, along with a
Threshold value that the manufacturer has determined will indi-
cate that the disk is going to fail, or that it has exceeded its
design age or aging limit. smartctl does not calculate any of
the Attribute values, thresholds, or types, it merely reports
them from the SMART data on the device.
Note that starting with ATA/ATAPI-4, revision 4, the meaning of
these Attribute fields has been made entirely vendor-specific.
However most newer ATA/SATA disks seem to respect their meaning,
so we have retained the option of printing the Attribute values.
Solid-state drives use different meanings for some of the attrib-
utes. In this case the attribute name printed by smartctl is in-
correct unless the drive is already in the smartmontools drive
database.
Note that the ATA command SMART READ DATA was declared obsolete
in ATA ACS-4 Revision 10 (Nov 2015).
[SCSI] For SCSI devices the "attributes" are obtained from the
temperature and start-stop cycle counter log pages. Certain ven-
dor specific attributes are listed if recognised. The attributes
are output in a relatively free format (compared with ATA disk
attributes).
[NVMe] For NVMe devices the attributes are obtained from the
SMART/Health Information log.
-f FORMAT, --format=FORMAT
[ATA only] Selects the output format of the attributes:
old - Old smartctl format. This is the default unless the '-x'
option is specified.
brief - New format which fits into 80 columns (except in some
rare cases). This format also decodes four additional attribute
flags. This is the default if the '-x' option is specified.
hex,id - Print all attribute IDs as hexadecimal numbers.
hex,val - Print all normalized values as hexadecimal numbers.
hex - Same as '-f hex,id -f hex,val'.
-l TYPE, --log=TYPE
Prints various device logs. The valid arguments to this option
are:
error - [ATA] prints the Summary SMART error log. SMART disks
maintain a log of the most recent five non-trivial errors. For
each of these errors, the disk power-on lifetime at which the er-
ror occurred is recorded, as is the device status (idle, standby,
etc) at the time of the error. For some common types of errors,
the Error Register (ER) and Status Register (SR) values are de-
coded and printed as text. The meanings of these are:
ABRT: Command ABoRTed
AMNF: Address Mark Not Found
CCTO: Command Completion Timed Out
EOM: End Of Media
ICRC: Interface Cyclic Redundancy Code (CRC) error
IDNF: IDentity Not Found
ILI: (packet command-set specific)
MC: Media Changed
MCR: Media Change Request
NM: No Media
obs: obsolete
TK0NF: TracK 0 Not Found
UNC: UNCorrectable Error in Data
WP: Media is Write Protected
In addition, up to the last five commands that preceded the error
are listed, along with a timestamp measured from the start of the
corresponding power cycle. This is displayed in the form
Dd+HH:MM:SS.msec where D is the number of days, HH is hours, MM
is minutes, SS is seconds and msec is milliseconds. [Note: this
time stamp wraps after 2^32 milliseconds, or 49 days 17 hours 2
minutes and 47.296 seconds.] The key ATA disk registers are also
recorded in the log. The final column of the error log is a
text-string description of the ATA command defined by the Command
Register (CR) and Feature Register (FR) values. Commands that
are obsolete in the most current spec are listed like this: READ
LONG (w/ retry) [OBS-4], indicating that the command became obso-
lete with or in the ATA-4 specification. Similarly, the notation
[RET-N] is used to indicate that a command was retired in the
ATA-N specification. Some commands are not defined in any ver-
sion of the ATA specification but are in common use nonetheless;
these are marked [NS], meaning non-standard.
The ATA Specification (ATA ACS-2 Revision 7, Section A.7.1) says:
"Error log data structures shall include, but are not limited to,
Uncorrectable errors, ID Not Found errors for which the LBA re-
quested was valid, servo errors, and write fault errors. Error
log data structures shall not include errors attributed to the
receipt of faulty commands." The definitions of these terms are:
UNC (UNCorrectable): data is uncorrectable. This refers to data
which has been read from the disk, but for which the Error Check-
ing and Correction (ECC) codes are inconsistent. In effect, this
means that the data can not be read.
IDNF (ID Not Found): user-accessible address could not be found.
For READ LOG type commands, IDNF can also indicate that a device
data log structure checksum was incorrect.
If the command that caused the error was a READ or WRITE command,
then the Logical Block Address (LBA) at which the error occurred
will be printed in base 10 and base 16. The LBA is a linear ad-
dress, which counts 512-byte sectors on the disk, starting from
zero. (Because of the limitations of the SMART error log, if the
LBA is greater than 0xfffffff, then either no error log entry
will be made, or the error log entry will have an incorrect LBA.
This may happen for drives with a capacity greater than 128 GiB
or 137 GB.) On Linux systems the smartmontools web page has in-
structions about how to convert the LBA address to the name of
the disk file containing the erroneous disk sector.
Please note that some manufacturers ignore the ATA specifica-
tions, and make entries in the error log if the device receives a
command which is not implemented or is not valid.
error - [SCSI] prints the error counter log pages for reads,
write and verifies. The verify row is only output if it has an
element other than zero.
error[,NUM] - [NVMe] prints the NVMe Error Information log. Only
the 16 most recent log entries are printed by default. This num-
ber can be changed by the optional parameter NUM. The maximum
number of log entries is vendor specific (in the range from 1 to
256 inclusive).
Note that the contents of this log is not preserved across power
cycles or controller resets, but the value of 'Error Information
Log Entries' from SMART/Health Information log is.
xerror[,NUM][,error] - [ATA only] prints the Extended Comprehen-
sive SMART error log (General Purpose Log address 0x03). Unlike
the Summary SMART error log (see '-l error' above), it provides
sufficient space to log the contents of the 48-bit LBA register
set introduced with ATA-6. It also supports logs with more than
one sector. Each sector holds up to 4 log entries. The actual
number of log sectors is vendor specific.
Only the 8 most recent error log entries are printed by default.
This number can be changed by the optional parameter NUM.
If ',error' is appended and the Extended Comprehensive SMART er-
ror log is not supported, the Summary SMART self-test log is
printed.
Please note that recent drives may report errors only in the Ex-
tended Comprehensive SMART error log. The Summary SMART error
log may be reported as supported but is always empty then.
selftest - [ATA] prints the SMART self-test log. The disk main-
tains a self-test log showing the results of the self tests,
which can be run using the '-t' option described below. For each
of the most recent twenty-one self-tests, the log shows the type
of test (short or extended, off-line or captive) and the final
status of the test. If the test did not complete successfully,
then the percentage of the test remaining is shown. The time at
which the test took place, measured in hours of disk lifetime, is
also printed. [Note: this time stamp wraps after 2^16 hours, or
2730 days and 16 hours, or about 7.5 years.] If any errors were
detected, the Logical Block Address (LBA) of the first error is
printed in decimal notation.
selftest - [SCSI] the self-test log for a SCSI device has a
slightly different format than for an ATA device. For each of
the most recent twenty self-tests, it shows the type of test and
the status (final or in progress) of the test. SCSI standards
use the terms "foreground" and "background" (rather than ATA's
corresponding "captive" and "off-line") and "short" and "long"
(rather than ATA's corresponding "short" and "extended") to de-
scribe the type of the test. The printed segment number is only
relevant when a test fails in the third or later test segment.
It identifies the test that failed and consists of either the
number of the segment that failed during the test, or the number
of the test that failed and the number of the segment in which
the test was run, using a vendor-specific method of putting both
numbers into a single byte. The Logical Block Address (LBA) of
the first error is printed in hexadecimal notation. If provided,
the SCSI Sense Key (SK), Additional Sense Code (ASC) and Addi-
tional Sense Code Qualifier (ASCQ) are also printed. The self
tests can be run using the '-t' option described below (using the
ATA test terminology).
selftest - [NVMe: NEW EXPERIMENTAL SMARTCTL 7.4 FEATURE] prints
the NVMe self-test log.
xselftest[,NUM][,selftest] - [ATA only] prints the Extended SMART
self-test log (General Purpose Log address 0x07). Unlike the
SMART self-test log (see '-l selftest' above), it supports 48-bit
LBA and logs with more than one sector. Each sector holds up to
19 log entries. The actual number of log sectors is vendor spe-
cific.
Only the 25 most recent log entries are printed by default. This
number can be changed by the optional parameter NUM.
If ',selftest' is appended and the Extended SMART self-test log
is not supported, the old SMART self-test log is printed.
selective - [ATA only] Please see the '-t select' option below
for a description of selective self-tests. The selective self-
test log shows the start/end Logical Block Addresses (LBA) of
each of the five test spans, and their current test status. If
the span is being tested or the remainder of the disk is being
read-scanned, the current 65536-sector block of LBAs being tested
is also displayed. The selective self-test log also shows if a
read-scan of the remainder of the disk will be carried out after
the selective self-test has completed (see '-t afterselect' op-
tion) and the time delay before restarting this read-scan if it
is interrupted (see '-t pending' option).
directory[,gs] - [ATA only] if the device supports the General
Purpose Logging feature set (ATA-6 and above) then this prints
the Log Directory (the log at address 0). The Log Directory
shows what logs are available and their length in sectors (512
bytes). The contents of the logs at address 1 [Summary SMART er-
ror log] and at address 6 [SMART self-test log] may be printed
using the previously-described error and selftest arguments to
this option. If your version of smartctl supports 48-bit ATA
commands, both the General Purpose Log (GPL) and SMART Log (SL)
directories are printed in one combined table. The output can be
restricted to the GPL directory or SL directory by '-l direc-
tory,q' or '-l directory,s' respectively.
background - [SCSI only] the background scan results log outputs
information derived from Background Media Scans (BMS) done after
power up and/or periodically (e.g. every 24 hours) on recent SCSI
disks. If supported, the BMS status is output first, indicating
whether a background scan is currently underway (and if so a
progress percentage), the amount of time the disk has been pow-
ered up and the number of scans already completed. Then there is
a header and a line for each background scan "event". These will
typically be either recovered or unrecoverable errors. That lat-
ter group may need some attention. There is a description of the
background scan mechanism in section 4.18 of SBC-3 revision 6
(see www.t10.org ).
scttemp, scttempsts, scttemphist - [ATA only] prints the disk
temperature information provided by the SMART Command Transport
(SCT) commands. The option 'scttempsts' prints current tempera-
ture and temperature ranges returned by the SCT Status command,
'scttemphist' prints temperature limits and the temperature his-
tory table returned by the SCT Data Table command, and 'scttemp'
prints both. The temperature values are preserved across power
cycles. The logging interval can be configured with the '-l sct-
tempint,N[,p]' option, see below. The SCT commands were intro-
duced in ATA8-ACS and were also supported by many ATA-7 disks.
scttempint,N[,p] - [ATA only] clears the SCT temperature history
table and sets the time interval for temperature logging to N
minutes. If ',p' is specified, the setting is preserved across
power cycles. Otherwise, the setting is volatile and will be re-
verted to the last non-volatile setting by the next hard reset.
The default interval is vendor specific, typical values are 1, 2,
or 5 minutes.
scterc[,READTIME,WRITETIME][,p|reset] - [ATA only] prints values
and descriptions of the SCT Error Recovery Control settings.
These are equivalent to TLER (as used by Western Digital), CCTL
(as used by Samsung and Hitachi/HGST) and ERC (as used by Sea-
gate). READTIME and WRITETIME arguments (deciseconds) set the
specified values. Values of 0 disable the feature, other values
less than 65 are probably not supported. For RAID configura-
tions, this is typically set to 70,70 deciseconds.
[NEW EXPERIMENTAL SMARTCTL 7.3 FEATURE] If 'scterc,READ-
TIME,WRITETIME,p' is specified, these time values will be persis-
tent over a power-on reset. If 'scterc,p' is specified, the per-
sistent over power-on values are printed. If 'scterc,reset' is
specified, all SCT timer settings are restored to the manufac-
turer's default value. The ',p' and ',reset' options require the
device to support ATA ACS-4 or higher.
devstat[,PAGE] - [ATA only] prints values and descriptions of the
ATA Device Statistics log pages (General Purpose Log address
0x04). If no PAGE number is specified, entries from all sup-
ported pages are printed. If PAGE 0 is specified, the list of
supported pages is printed. Device Statistics was introduced in
ACS-2 and is only supported by some recent devices.
defects[,NUM] - [ATA] prints LBA and hours values from the ATA
Pending Defects log (General Purpose Log address 0x0c). Only the
31 entries from first log page are printed by default. This num-
ber can be changed by the optional parameter NUM. The size of
the log and the order of the entries are vendor specific. The
Pending Defects log was introduced in ACS-4 Revision 01 (Mar
2014).
defects - [SCSI: NEW EXPERIMENTAL SMARTCTL 7.3 FEATURE] prints
LBAs that the background scan was unable to read (i.e. a defect).
Entries, if any, show the defective LBA and the value of the
power-on hours (since manufacture) when the background scan found
the defect. Note these pending defects may appear in advance of
any application trying to read a defective LBA.
envrep - [SCSI only: NEW EXPERIMENTAL SMARTCTL 7.3 FEATURE]
prints values and descriptions of the SCSI Environmental report-
ing log page. This includes one or more temperatures and may in-
clude relative humidities. Lifetime maximums and minimums are
also reported.
genstats - [SCSI only: NEW EXPERIMENTAL SMARTCTL 7.4 FEATURE]
prints values and descriptions of the SCSI General statistics and
performance log page.
sataphy[,reset] - [SATA only] prints values and descriptions of
the SATA Phy Event Counters (General Purpose Log address 0x11).
If '-l sataphy,reset' is specified, all counters are reset after
reading the values. This also works for SATA devices with Packet
interface like CD/DVD drives.
sasphy[,reset] - [SAS (SCSI) only] prints values and descriptions
of the SAS (SSP) Protocol Specific log page (log page 0x18). If
'-l sasphy,reset' is specified, all counters are reset after
reading the values.
tapealert - [SCSI tape drives and changers: NEW EXPERIMENTAL
SMARTCTL 7.3 FEATURE] prints values and descriptions of the (SSC)
Tape Alert log page. See TAPE DRIVES below for issue associated
with printing this log page.
tapedevstat - [SCSI tape drives and changers: NEW EXPERIMENTAL
SMARTCTL 7.3 FEATURE] prints values and descriptions of the (SSC)
Device Statistics log page.
zdevstat - [SCSI zoned disks: NEW EXPERIMENTAL SMARTCTL 7.3 FEA-
TURE] prints values and descriptions of the Zoned Block Device
Statistics log page (ZBC-2).
gplog,ADDR[,FIRST[-LAST|+SIZE]] - [ATA only] prints a hex dump of
any log accessible via General Purpose Logging (GPL) feature.
The log address ADDR is the hex address listed in the log direc-
tory (see '-l directory' above). The range of log sectors
(pages) can be specified by decimal values FIRST-LAST or
FIRST+SIZE. FIRST defaults to 0, SIZE defaults to 1. LAST can
be set to 'max' to specify the last page of the log.
smartlog,ADDR[,FIRST[-LAST|+SIZE]] - [ATA only] prints a hex dump
of any log accessible via SMART Read Log command. See '-l
gplog,...' above for parameter syntax.
For example, all these commands:
smartctl -l gplog,0x80,10-15 /dev/sda
smartctl -l gplog,0x80,10+6 /dev/sda
smartctl -l smartlog,0x80,10-15 /dev/sda
print pages 10–15 of log 0x80 (first host vendor specific log).
The hex dump format is compatible with the 'xxd -r' command.
This command:
smartctl -l gplog,0x11 /dev/sda | grep ^0 | xxd -r >log.bin
writes a binary representation of the one sector log 0x11 (SATA
Phy Event Counters) to file log.bin.
nvmelog,PAGE,SIZE - [NVMe only] prints a hex dump of the first
SIZE bytes from the NVMe log with identifier PAGE. PAGE is a
hexadecimal number in the range from 0x1 to 0xff. SIZE is a
hexadecimal number in the range from 0x4 to 0x4000 (16 KiB).
WARNING: Do not specify the identifier of an unknown log page.
Reading a log page may have undesirable side effects.
ssd - [ATA] prints the Solid State Device Statistics log page.
This has the same effect as '-l devstat,7', see above.
ssd - [SCSI] prints the Solid State Media percentage used en-
durance indicator. A value of 0 indicates as new condition while
100 indicates the device is at the end of its lifetime as pro-
jected by the manufacturer. The value may reach 255.
farm - [Seagate ATA or SAS (SCSI) only: NEW EXPERIMENTAL SMARTCTL
7.4 FEATURE] prints predictive drive health metrics and values
from Seagate's vendor-specific Field Access Reliability Metrics
(FARM) log when used on a drive supporting FARM. ATA and SAS
logs differ slightly. WARNING: Some Seagate drives do not sup-
port FARM.
-v ID,FORMAT[:BYTEORDER][,NAME], --vendorattribute=ID,FORMAT...
[ATA only] Sets a vendor-specific raw value print FORMAT, an op-
tional BYTEORDER and an optional NAME for Attribute ID. This op-
tion may be used multiple times.
The Attribute ID can be in the range 1 to 255. If 'N' is speci-
fied as ID, the settings for all Attributes are changed.
The optional BYTEORDER consists of 1 to 8 characters from the set
'012345rvwz'. The characters '0' to '5' select the byte 0 to 5
from the 48-bit raw value, 'r' selects the reserved byte of the
attribute data block, 'v' selects the normalized value, 'w' se-
lects the worst value and 'z' inserts a zero byte. The default
BYTEORDER is '543210' for all 48-bit formats, 'r543210' for the
54-bit formats, and '543210wv' for the 64-bit formats. For exam-
ple, '-v 5,raw48:012345' prints the raw value of attribute 5 with
big endian instead of little endian byte ordering.
The NAME is a string of letters, digits and underscore. Its
length should not exceed 23 characters. The '-P showall' option
reports an error if this is the case.
-v help - Prints (to STDOUT) a list of all valid arguments to
this option, then exits.
Valid arguments for FORMAT are:
raw8 - Print the Raw value as six 8-bit unsigned base-10 inte-
gers. This may be useful for decoding the meaning of the Raw
value.
raw16 - Print the Raw value as three 16-bit unsigned base-10 in-
tegers. This may be useful for decoding the meaning of the Raw
value.
raw48 - Print the Raw value as a 48-bit unsigned base-10 integer.
This is the default for most attributes.
hex48 - Print the Raw value as a 12 digit hexadecimal number.
This may be useful for decoding the meaning of the Raw value.
raw56 - Print the Raw value as a 54-bit unsigned base-10 integer.
This includes the reserved byte which follows the 48-bit raw
value.
hex56 - Print the Raw value as a 14 digit hexadecimal number.
This includes the reserved byte which follows the 48-bit raw
value.
raw64 - Print the Raw value as a 64-bit unsigned base-10 integer.
This includes two bytes from the normalized and worst attribute
value. This raw format is used by some SSD devices with Indilinx
controller.
hex64 - Print the Raw value as a 16 digit hexadecimal number.
This includes two bytes from the normalized and worst attribute
value. This raw format is used by some SSD devices with Indilinx
controller.
min2hour - Raw Attribute is power-on time in minutes. Its raw
value will be displayed in the form "Xh+Ym". Here X is hours,
and Y is minutes in the range 0–59 inclusive. Y is always
printed with two digits, for example "06" or "31" or "00".
sec2hour - Raw Attribute is power-on time in seconds. Its raw
value will be displayed in the form "Xh+Ym+Zs". Here X is hours,
Y is minutes in the range 0–59 inclusive, and Z is seconds in the
range 0–59 inclusive. Y and Z are always printed with two dig-
its, for example "06" or "31" or "00".
halfmin2hour - Raw Attribute is power-on time, measured in units
of 30 seconds. This format is used by some Samsung disks. Its
raw value will be displayed in the form "Xh+Ym". Here X is
hours, and Y is minutes in the range 0–59 inclusive. Y is always
printed with two digits, for example "06" or "31" or "00".
msec24hour32 - Raw Attribute is power-on time measured in 32-bit
hours and 24-bit milliseconds since last hour update. It will be
displayed in the form "Xh+Ym+Z.Ms". Here X is hours, Y is min-
utes, Z is seconds and M is milliseconds.
tempminmax - Raw Attribute is the disk temperature in Celsius.
Info about Min/Max temperature is printed if available. This is
the default for Attributes 190 and 194. The recording interval
(lifetime, last power cycle, last soft reset) of the min/max val-
ues is device specific.
temp10x - Raw Attribute is ten times the disk temperature in Cel-
sius.
raw16(raw16) - Print the raw attribute as a 16-bit value and two
optional 16-bit values if these words are nonzero. This is the
default for Attributes 5 and 196.
raw16(avg16) - Raw attribute is spin-up time. It is printed as a
16-bit value and an optional "Average" 16-bit value if the word
is nonzero. This is the default for Attribute 3.
raw24(raw8) - Print the raw attribute as a 24-bit value and three
optional 8-bit values if these bytes are nonzero. This is the
default for Attribute 9.
raw24/raw24 - Raw Attribute contains two 24-bit values. The
first is the number of load cycles. The second is the number of
unload cycles. The difference between these two values is the
number of times that the drive was unexpectedly powered off (also
called an emergency unload). As a rule of thumb, the mechanical
stress created by one emergency unload is equivalent to that cre-
ated by one hundred normal unloads.
raw24/raw32 - Raw attribute is an error rate which consists of a
24-bit error count and a 32-bit total count.
The following old arguments to '-v' are also still valid:
9,minutes - same as: 9,min2hour,Power_On_Minutes.
9,seconds - same as: 9,sec2hour,Power_On_Seconds.
9,halfminutes - same as: 9,halfmin2hour,Power_On_Half_Minutes.
9,temp - same as: 9,tempminmax,Temperature_Celsius.
192,emergencyretractcyclect - same as: 192,raw48,Emerg_Re-
tract_Cycle_Ct
193,loadunload - same as: 193,raw24/raw24.
194,10xCelsius - same as: 194,temp10x,Temperature_Celsius_x10.
194,unknown - same as: 194,raw48,Unknown_Attribute.
197,increasing - same as: 197,raw48,Total_Pending_Sectors. Also
means that Attribute number 197 (Current Pending Sector Count) is
not reset if uncorrectable sectors are reallocated (see
smartd.conf(5) man page).
198,increasing - same as: 198,raw48,Total_Offl_Uncorrectabl.
Also means that Attribute number 198 (Offline Uncorrectable Sec-
tor Count) is not reset if uncorrectable sectors are reallocated
(see smartd.conf(5) man page).
198,offlinescanuncsectorct - same as: 198,raw48,Of-
fline_Scan_UNC_SectCt.
200,writeerrorcount - same as: 200,raw48,Write_Error_Count.
201,detectedtacount - same as: 201,raw48,Detected_TA_Count.
220,temp - same as: 220,tempminmax,Temperature_Celsius.
-F TYPE, --firmwarebug=TYPE
[ATA only] Modifies the behavior of smartctl to compensate for
some known and understood device firmware or driver bug. This
option may be used multiple times. The valid arguments are:
none - Assume that the device firmware obeys the ATA specifica-
tions. This is the default, unless the device has presets for
'-F' in the drive database. Using this option on the command
line will override any preset values.
nologdir - Suppresses read attempts of SMART or GP Log Directory.
Support for all standard logs is assumed without an actual check.
Some Intel SSDs may freeze if log address 0 is read.
samsung - In some Samsung disks (example: model SV4012H Firmware
Version: RM100-08) some of the two- and four-byte quantities in
the SMART data structures are byte-swapped (relative to the ATA
specification). Enabling this option tells smartctl to evaluate
these quantities in byte-reversed order. Some signs that your
disk needs this option are (1) no self-test log printed, even
though you have run self-tests; (2) very large numbers of ATA er-
rors reported in the ATA error log; (3) strange and impossible
values for the ATA error log timestamps.
samsung2 - In some Samsung disks the number of ATA errors re-
ported is byte swapped. Enabling this option tells smartctl to
evaluate this quantity in byte-reversed order. An indication
that your Samsung disk needs this option is that the self-test
log is printed correctly, but there are a very large number of
errors in the SMART error log. This is because the error count
is byte swapped. Thus a disk with five errors (0x0005) will ap-
pear to have 20480 errors (0x5000).
samsung3 - Some Samsung disks (at least SP2514N with Firmware
VF100-37) report a self-test still in progress with 0% remaining
when the test was already completed. Enabling this option modi-
fies the output of the self-test execution status (see options
'-c' or '-a' above) accordingly.
xerrorlba - Fixes LBA byte ordering in Extended Comprehensive
SMART error log. Some disks use little endian byte ordering in-
stead of ATA register ordering to specify the LBA addresses in
the log entries.
swapid - Fixes byte swapped ATA identify strings (device name,
serial number, firmware version) returned by some buggy device
drivers.
-P TYPE, --presets=TYPE
[ATA only] Specifies whether smartctl should use any preset op-
tions that are available for this drive. By default, if the
drive is recognized in the smartmontools database, then the pre-
sets are used.
The argument show will show any preset options for your drive and
the argument showall will show all known drives in the smartmon-
tools database, along with their preset options. If there are no
presets for your drive and you think there should be (for exam-
ple, a -v or -F option is needed to get smartctl to display cor-
rect values) then please contact the smartmontools developers so
that this information can be added to the smartmontools database.
Contact information is at the end of this man page.
The valid arguments to this option are:
use - if a drive is recognized, then use the stored presets for
it. This is the default. Note that presets will NOT override
additional Attribute interpretation ('-v N,something') command-
line options or explicit '-F' command-line options..
ignore - do not use presets.
show - show if the drive is recognized in the database, and if
so, its presets, then exit.
showall - list all recognized drives, and the presets that are
set for them, then exit. This also checks the drive database
regular expressions and settings for syntax errors.
The '-P showall' option takes up to two optional arguments to
match a specific drive type and firmware version. The command:
smartctl -P showall
lists all entries, the command:
smartctl -P showall 'MODEL'
lists all entries matching MODEL, and the command:
smartctl -P showall 'MODEL' 'FIRMWARE'
lists all entries for this MODEL and a specific FIRMWARE version.
-B [+]FILE, --drivedb=[+]FILE
[ATA only] Read the drive database from FILE. The new database
replaces the built in database by default. If '+' is specified,
then the new entries prepend the built in entries.
Optional entries are read from the file /etc/smart_drivedb.h if
this option is not specified.
If /var/lib/smartmontools/drivedb/drivedb.h is present, the con-
tents of this file is used instead of the built in table.
Run /usr/sbin/update-smart-drivedb to update this file from the
smartmontools SVN repository.
The database files use the same C/C++ syntax that is used to ini-
tialize the built in database array. C/C++ style comments are
allowed. Example:
/* Full entry: */
{
"Model family", // Info about model family/series.
"MODEL1.*REGEX", // Regular expression to match model of device.
"VERSION.*REGEX", // Regular expression to match firmware version(s).
"Some warning", // Warning message.
"-v 9,minutes" // String of preset -v and -F options.
},
/* Minimal entry: */
{
"", // No model family/series info.
"MODEL2.*REGEX", // Regular expression to match model of device.
"", // All firmware versions.
"", // No warning.
"" // No options preset.
},
/* USB ID entry: */
{
"USB: Device; Bridge", // Info about USB device and bridge name.
"0x1234:0xabcd", // Regular expression to match vendor:product ID.
"0x0101", // Regular expression to match bcdDevice.
"", // Not used.
"-d sat" // String with device type option.
},
/* ... */
SMART RUN/ABORT OFFLINE TEST AND self-test OPTIONS:
-t TEST, --test=TEST
Executes TEST immediately. The '-C' option can be used in con-
junction with this option to run the short or long (and also for
ATA devices, selective or conveyance) self-tests in captive mode
(known as "foreground mode" for SCSI devices). Note that only
one test type can be run at a time, so only one test type should
be specified per command line. Note also that if a computer is
shutdown or power cycled during a self-test, no harm should re-
sult. The self-test will either be aborted or will resume auto-
matically.
All '-t TEST' commands can be given during normal system opera-
tion unless captive mode ('-C' option) is used. A running self-
test can, however, degrade performance of the drive. Frequent
I/O requests from the operating system increase the duration of a
test. These impacts may vary from device to device.
If a test failure occurs then the device may discontinue the
testing and report the result immediately.
[ATA] Note that the ATA command SMART EXECUTE OFF-LINE IMMEDIATE
(the command to start a test) was declared obsolete in ATA ACS-4
Revision 10 (Nov 2015).
The valid arguments to this option are:
offline - [ATA] runs SMART Immediate Offline Test. This immedi-
ately starts the test described above. This command can be given
during normal system operation. The effects of this test are
visible only in that it updates the SMART Attribute values, and
if errors are found they will appear in the SMART error log, vis-
ible with the '-l error' option.
If the '-c' option to smartctl shows that the device has the
"Suspend Offline collection upon new command" capability then you
can track the progress of the Immediate Offline test using the
'-c' option to smartctl. If the '-c' option show that the device
has the "Abort Offline collection upon new command" capability
then most commands will abort the Immediate Offline Test, so you
should not try to track the progress of the test with '-c', as it
will abort the test.
offline - [SCSI] runs the default self test in foreground. No
entry is placed in the self test log.
short - [ATA] runs SMART Short Self Test (usually under ten min-
utes). This command can be given during normal system operation
(unless run in captive mode - see the '-C' option below). This
is a test in a different category than the immediate or automatic
offline tests. The "Self" tests check the electrical and mechan-
ical performance as well as the read performance of the disk.
Their results are reported in the Self Test Error Log, readable
with the '-l selftest' option. Note that on some disks the
progress of the self-test can be monitored by watching this log
during the self-test; with other disks use the '-c' option to
monitor progress.
short - [SCSI] runs the "Background short" self-test.
short - [NVMe: NEW EXPERIMENTAL SMARTCTL 7.4 FEATURE] runs the
"Short" self-test for current namespace.
long - [ATA] runs SMART Extended Self Test (tens of minutes to
several hours). This is a longer and more thorough version of
the Short Self Test described above. Note that this command can
be given during normal system operation (unless run in captive
mode - see the '-C' option below).
long - [SCSI] runs the "Background long" self-test.
long - [NVMe: NEW EXPERIMENTAL SMARTCTL 7.4 FEATURE] runs the
"Extended" self-test for current namespace.
conveyance - [ATA only] runs a SMART Conveyance Self Test (min-
utes). This self-test routine is intended to identify damage in-
curred during transporting of the device. This self-test routine
should take on the order of minutes to complete. Note that this
command can be given during normal system operation (unless run
in captive mode - see the '-C' option below).
select,N-M, select,N+SIZE - [ATA only] runs a SMART Selective
Self Test, to test a range of disk Logical Block Addresses
(LBAs), rather than the entire disk. Each range of LBAs that is
checked is called a "span" and is specified by a starting LBA (N)
and an ending LBA (M) with N less than or equal to M. The range
can also be specified as N+SIZE. A span at the end of a disk can
be specified by N-max.
For example the commands:
smartctl -t select,10-20 /dev/sda
smartctl -t select,10+11 /dev/sda
both runs a self test on one span consisting of LBAs ten to
twenty (inclusive). The command:
smartctl -t select,100000000-max /dev/sda
run a self test from LBA 100000000 up to the end of the disk.
The '-t' option can be given up to five times, to test up to five
spans. For example the command:
smartctl -t select,0-100 -t select,1000-2000 /dev/sda
runs a self test on two spans. The first span consists of 101
LBAs and the second span consists of 1001 LBAs. Note that the
spans can overlap partially or completely, for example:
smartctl -t select,0-10 -t select,5-15 -t select,10-20 /dev/sda
The results of the selective self-test can be obtained (both dur-
ing and after the test) by printing the SMART self-test log, us-
ing the '-l selftest' option to smartctl.
Selective self tests are particularly useful as disk capacities
increase: an extended self test (smartctl -t long) can take sev-
eral hours. Selective self-tests are helpful if (based on SYSLOG
error messages, previous failed self-tests, or SMART error log
entries) you suspect that a disk is having problems at a particu-
lar range of Logical Block Addresses (LBAs).
Selective self-tests can be run during normal system operation
(unless done in captive mode - see the '-C' option below).
The following variants of the selective self-test command use
spans based on the ranges from past tests already stored on the
disk:
select,redo[+SIZE] - [ATA only] redo the last SMART Selective
Self Test using the same LBA range. The starting LBA is identi-
cal to the LBA used by last test, same for ending LBA unless a
new span size is specified by optional +SIZE argument.
For example the commands:
smartctl -t select,10-20 /dev/sda
smartctl -t select,redo /dev/sda
smartctl -t select,redo+20 /dev/sda
have the same effect as:
smartctl -t select,10-20 /dev/sda
smartctl -t select,10-20 /dev/sda
smartctl -t select,10-29 /dev/sda
select,next[+SIZE] - [ATA only] runs a SMART Selective Self Test
on the LBA range which follows the range of the last test. The
starting LBA is set to (ending LBA +1) of the last test. A new
span size may be specified by the optional +SIZE argument.
For example the commands:
smartctl -t select,0-999 /dev/sda
smartctl -t select,next /dev/sda
smartctl -t select,next+2000 /dev/sda
have the same effect as:
smartctl -t select,0-999 /dev/sda
smartctl -t select,1000-1999 /dev/sda
smartctl -t select,2000-3999 /dev/sda
If the last test ended at the last LBA of the disk, the new range
starts at LBA 0. The span size of the last span of a disk is ad-
justed such that the total number of spans to check the full disk
will not be changed by future uses of '-t select,next'.
select,cont[+SIZE] - [ATA only] performs a 'redo' (above) if the
self test status reports that the last test was aborted by the
host. Otherwise it run the 'next' (above) test.
afterselect,on - [ATA only] perform an offline read scan after a
Selective self-test has completed. This option must be used to-
gether with one or more of the select,N-M options above. If the
LBAs that have been specified in the Selective self-test pass the
test with no errors found, then read scan the remainder of the
disk. If the device is powered-cycled while this read scan is in
progress, the read scan will be automatically resumed after a
time specified by the pending timer (see below). The value of
this option is preserved between selective self-tests.
afterselect,off - [ATA only] do not read scan the remainder of
the disk after a Selective self-test has completed. This option
must be use together with one or more of the select,N-M options
above. The value of this option is preserved between selective
self-tests.
pending,N - [ATA only] set the pending offline read scan timer to
N minutes. Here N is an integer in the range from 0 to 65535 in-
clusive. If the device is powered off during a read scan after a
Selective self-test, then resume the test automatically N minutes
after power-up. This option must be use together with one or
more of the select,N-M options above. The value of this option
is preserved between selective self-tests.
vendor,N - [ATA only] issues the ATA command SMART EXECUTE OFF-
LINE IMMEDIATE with subcommand N in LBA LOW register. The sub-
command is specified as a hex value in the range 0x00 to 0xff.
Subcommands 0x40–0x7e and 0x90–0xff are reserved for vendor spe-
cific use, see table 61 of T13/1699-D Revision 6a (ATA8-ACS).
Note that the subcommands 0x00–0x04, 0x7f, 0x81–0x84 are sup-
ported by other smartctl options (e.g. 0x01: '-t short', 0x7f:
'-X', 0x82: '-C -t long').
WARNING: Only run subcommands documented by the vendor of the de-
vice.
Example for some Intel SSDs only: The subcommand 0x40 ('-t ven-
dor,0x40') clears the timed workload related SMART attributes
(226, 227, 228). Note that the raw values of these attributes
are held at 65535 (0xffff) until the workload timer reaches 60
minutes.
force - start new self-test even if another test is already run-
ning. By default a running self-test will not be interrupted to
begin another test.
-C, --captive
[ATA] Runs self-tests in captive mode. This has no effect with
'-t offline' or if the '-t' option is not used.
WARNING: Tests run in captive mode may busy out the drive for the
length of the test. Only run captive tests on drives without any
mounted partitions!
[SCSI] Runs the self-test in "Foreground" mode.
-X, --abort
Aborts non-captive SMART Self Tests. Note that this command will
abort the Offline Immediate Test routine only if your disk has
the "Abort Offline collection upon new command" capability.
ATA, SCSI command sets and SAT
In the past there has been a clear distinction between storage devices
that used the ATA and SCSI command sets. This distinction was often re-
flected in their device naming and hardware. Now various SCSI trans-
ports (e.g. SAS, FC and iSCSI) can interconnect to both SCSI disks (e.g.
FC and SAS) and ATA disks (especially SATA). USB and IEEE 1394 storage
devices use the SCSI command set externally but almost always contain
ATA or SATA disks (or flash). The storage subsystems in some operating
systems have started to remove the distinction between ATA and SCSI in
their device naming policies.
99% of operations that an OS performs on a disk involve the SCSI IN-
QUIRY, READ CAPACITY, READ and WRITE commands, or their ATA equivalents.
Since the SCSI commands are slightly more general than their ATA equiva-
lents, many OSes are generating SCSI commands (mainly READ and WRITE)
and letting a lower level translate them to their ATA equivalents as the
need arises. An important note here is that "lower level" may be in ex-
ternal equipment and hence outside the control of an OS.
SCSI to ATA Translation (SAT) is a standard (ANSI INCITS 431-2007) that
specifies how this translation is done. For the other 1% of operations
that an OS performs on a disk, SAT provides two options. First is an
optional ATA PASS-THROUGH SCSI command (there are two variants). The
second is a translation from the closest SCSI command. Most current in-
terest is in the "pass-through" option.
The relevance to smartmontools (and hence smartctl) is that its interac-
tions with disks fall solidly into the "1%" category. So even if the OS
can happily treat (and name) a disk as "SCSI", smartmontools needs to
detect the native command set and act accordingly. As more storage man-
ufacturers (including external SATA drives) comply with SAT, smartmon-
tools is able to automatically distinguish the native command set of the
device. In some cases the '-d sat' option is needed on the command
line.
There are also virtual disks which typically have no useful information
to convey to smartmontools, but could conceivably in the future. An ex-
ample of a virtual disk is the OS's view of a RAID 1 box. There are
most likely two SATA disks inside a RAID 1 box. Addressing those SATA
disks from a distant OS is a challenge for smartmontools. Another ap-
proach is running a tool like smartmontools inside the RAID 1 box (e.g.
a Network Attached Storage (NAS) box) and fetching the logs via a
browser.
TAPE DRIVES
Commands for SCSI Tape drives as defined in the SSC-4 standard (ANSI IN-
CITS 516-2013). SSC stands for "SCSI Streaming Commands". Draft stan-
dards can be found at <https://www.t10.org/> .
Many SMART related features of SCSI disks are shared by SCSI tape dri-
ves. One important tape-specific log page is called "TapeAlert" which
is used to report abnormal conditions. Unlike most other log pages the
TapeAlert log page clears pending alerts after that page is fetched
(i.e. read from the tape drive). To be more precise, the TapeAlert log
page is cleared for the I_T nexus (initiator-target pair) that sent the
(SCSI LOG SENSE) command; so another initiator (e.g. a HBA on another
machine) will still have pending alerts reported. [This clearing action
can be controlled by the TAPLSD bit is the [SSC] Device Configuration
Extension mode page but the original and default action remains: clear
any pending TapeAlerts. The sdparm utility can be used to access and
change TAPLSD.]
Previous versions of smartctl have supported polling the TapeAlert log
page when the --health option is given. This clearing of pending alerts
has created problems for other tape-specific tools. This version of
smartctl will only fetch the TapeAlert log page if the --health option
is given twice in the command line invocation (or the --log=tapealert
option is given).
There are other tape-specific log pages such as --log=tapedevstat that
behave normally (i.e. they don't change any state information in the
tape drive).
EXAMPLES
smartctl -a /dev/sda
Print a large amount of SMART information for drive /dev/sda.
smartctl -s off /dev/sdd
Disable SMART monitoring and data log collection on drive /dev/sdd.
smartctl --smart=on --offlineauto=on --saveauto=on /dev/sda
Enable SMART on drive /dev/sda, enable automatic offline testing every
four hours, and enable autosaving of SMART Attributes. This is a good
start-up line for your system's init files. You can issue this command
on a running system.
smartctl -t long /dev/sdc
Begin an extended self-test of drive /dev/sdc. You can issue this com-
mand on a running system. The results can be seen in the self-test log
visible with the '-l selftest' option after it has completed.
smartctl -s on -t offline /dev/sda
Enable SMART on the disk, and begin an immediate offline test of drive
/dev/sda. You can issue this command on a running system. The results
are only used to update the SMART Attributes, visible with the '-A' op-
tion. If any device errors occur, they are logged to the SMART error
log, which can be seen with the '-l error' option.
smartctl -A -v 9,minutes /dev/sda
Shows the vendor Attributes, when the disk stores its power-on time in-
ternally in minutes rather than hours.
smartctl -q errorsonly -H -l selftest /dev/sda
Produces output only if the device returns failing SMART status, or if
some of the logged self-tests ended with errors.
smartctl -q silent -a /dev/sda
Examine all SMART data for device /dev/sda, but produce no printed out-
put. You must use the exit status (the $? shell variable) to learn if
any Attributes are out of bound, if the SMART status is failing, if
there are errors recorded in the self-test log, or if there are errors
recorded in the disk error log.
smartctl -a -d 3ware,0 /dev/twl0
Examine all SMART data for the first SATA (not SAS) disk connected to a
3ware RAID 9750 controller card.
smartctl -t long -d areca,4 /dev/sg2
Start a long self-test on the fourth SATA disk connected to an Areca
RAID controller addressed by /dev/sg2.
smartctl -a -d hpt,1/3 /dev/sda (under Linux)
smartctl -a -d hpt,1/3 /dev/hptrr (under FreeBSD)
Examine all SMART data for the (S)ATA disk directly connected to the
third channel of the first HighPoint RocketRAID controller card.
smartctl -t short -d hpt,1/1/2 /dev/sda (under Linux)
smartctl -t short -d hpt,1/1/2 /dev/hptrr (under FreeBSD)
Start a short self-test on the (S)ATA disk connected to second pmport on
the first channel of the first HighPoint RocketRAID controller card.
smartctl -t select,10-100 -t select,30-300 -t afterselect,on -t pend-
ing,45 /dev/sda
Run a selective self-test on LBAs 10 to 100 and 30 to 300. After the
these LBAs have been tested, read-scan the remainder of the disk. If
the disk is power-cycled during the read-scan, resume the scan 45 min-
utes after power to the device is restored.
smartctl -a -d cciss,0 /dev/cciss/c0d0
Examine all SMART data for the first SCSI disk connected to a cciss RAID
controller card.
EXIT STATUS
The exit statuses of smartctl are defined by a bitmask. If all is well
with the disk, the exit status (return value) of smartctl is 0 (all bits
turned off). If a problem occurs, or an error, potential error, or
fault is detected, then a non-zero status is returned. In this case,
the eight different bits in the exit status have the following meanings
for ATA disks; some of these values may also be returned for SCSI disks.
Bit 0: Command line did not parse.
Bit 1: Device open failed, device did not return an IDENTIFY DEVICE
structure, or device is in a low-power mode (see '-n' option
above).
Bit 2: Some SMART or other ATA command to the disk failed, or there was
a checksum error in a SMART data structure (see '-b' option
above).
Bit 3: SMART status check returned "DISK FAILING".
Bit 4: We found prefail Attributes <= threshold.
Bit 5: SMART status check returned "DISK OK" but we found that some (us-
age or prefail) Attributes have been <= threshold at some time in
the past.
Bit 6: The device error log contains records of errors.
Bit 7: The device self-test log contains records of errors. [ATA only]
Failed self-tests outdated by a newer successful extended self-
test are ignored.
To test within the shell for whether or not the different bits are
turned on or off, you can use the following type of construction (which
should work with any POSIX compatible shell):
smartstat=$(($? & 8))
This looks at only at bit 3 of the exit status $? (since 8=2^3). The
shell variable $smartstat will be nonzero if SMART status check returned
"disk failing" and zero otherwise.
This shell script prints all status bits:
val=$?; mask=1
for i in 0 1 2 3 4 5 6 7; do
echo "Bit $i: $(((val & mask) && 1))"
mask=$((mask << 1))
done
FILES
/usr/sbin/smartctl
full path of this executable.
/var/lib/smartmontools/drivedb/drivedb.h
drive database (see '-B' option).
/etc/smart_drivedb.h
optional local drive database (see '-B' option).
AUTHORS
Bruce Allen (project initiator),
Christian Franke (project manager, Windows port and all sort of things),
Douglas Gilbert (SCSI subsystem),
Volker Kuhlmann (moderator of support and database mailing list),
Gabriele Pohl (wiki & development team support),
Alex Samorukov (FreeBSD port and more, new Trac wiki).
Many other individuals have made contributions and corrections, see AU-
THORS, ChangeLog and repository files.
The first smartmontools code was derived from the smartsuite package,
written by Michael Cornwell and Andre Hedrick.
REPORTING BUGS
To submit a bug report, create a ticket in smartmontools wiki:
<https://www.smartmontools.org/>.
Alternatively send the info to the smartmontools support mailing list:
<https://listi.jpberlin.de/mailman/listinfo/smartmontools-support>.
SEE ALSO
smartd(8).
update-smart-drivedb(8).
REFERENCES
Please see the following web site for more info: <https://www.smartmon-
tools.org/>
An introductory article about smartmontools is Monitoring Hard Disks
with SMART, by Bruce Allen, Linux Journal, January 2004, pages 74–77.
See <https://www.linuxjournal.com/article/6983>.
If you would like to understand better how SMART works, and what it
does, a good place to start is with Sections 4.8 and 6.54 of the first
volume of the 'AT Attachment with Packet Interface-7' (ATA/ATAPI-7)
specification Revision 4b. This documents the SMART functionality which
the smartmontools utilities provide access to.
The functioning of SMART was originally defined by the SFF-8035i revi-
sion 2 and the SFF-8055i revision 1.4 specifications. These are publi-
cations of the Small Form Factors (SFF) Committee.
Links to these and other documents may be found on the Links page of the
smartmontools Wiki at <https://www.smartmontools.org/wiki/Links>.
PACKAGE VERSION
smartmontools-7.4 2023-08-01 r5530
$Id: smartctl.8.in 5521 2023-07-24 16:44:49Z chrfranke $
smartmontools-7.4 2023-08-01 SMARTCTL(8)
Generated by dwww version 1.16 on Tue Dec 16 06:33:34 CET 2025.