RESIZE2FS(8) System Manager's Manual RESIZE2FS(8)
NAME
resize2fs - ext2/ext3/ext4 file system resizer
SYNOPSIS
resize2fs [ -fFpPMbs ] [ -d debug-flags ] [ -S RAID-stride ] [ -z
undo_file ] device [ size ]
DESCRIPTION
The resize2fs program will resize ext2, ext3, or ext4 file systems. It
can be used to enlarge or shrink an unmounted file system located on de-
vice. If the file system is mounted, it can be used to expand the size
of the mounted file system, assuming the kernel and the file system sup-
ports on-line resizing. (Modern Linux 2.6 kernels will support on-line
resize for file systems mounted using ext3 and ext4; ext3 file systems
will require the use of file systems with the resize_inode feature en-
abled.)
The size parameter specifies the requested new size of the file system.
If no units are specified, the units of the size parameter shall be the
file system blocksize of the file system. Optionally, the size parame-
ter may be suffixed by one of the following units designators: 'K', 'M',
'G', 'T' (either upper-case or lower-case) or 's' for power-of-two kilo-
bytes, megabytes, gigabytes, terabytes or 512 byte sectors respectively.
The size of the file system may never be larger than the size of the
partition. If size parameter is not specified, it will default to the
size of the partition.
The resize2fs program does not manipulate the size of partitions. If
you wish to enlarge a file system, you must make sure you can expand the
size of the underlying partition first. This can be done using fdisk(8)
by deleting the partition and recreating it with a larger size or using
lvextend(8), if you're using the logical volume manager lvm(8). When
recreating the partition, make sure you create it with the same starting
disk cylinder as before! Otherwise, the resize operation will certainly
not work, and you may lose your entire file system. After running
fdisk(8), run resize2fs to resize the ext2 file system to use all of the
space in the newly enlarged partition.
If you wish to shrink an ext2 partition, first use resize2fs to shrink
the size of file system. Then you may use fdisk(8) to shrink the size
of the partition. When shrinking the size of the partition, make sure
you do not make it smaller than the new size of the ext2 file system!
The -b and -s options enable and disable the 64bit feature, respec-
tively. The resize2fs program will, of course, take care of resizing
the block group descriptors and moving other data blocks out of the way,
as needed. It is not possible to resize the file system concurrent with
changing the 64bit status.
OPTIONS
-b Turns on the 64bit feature, resizes the group descriptors as nec-
essary, and moves other metadata out of the way.
-d debug-flags
Turns on various resize2fs debugging features, if they have been
compiled into the binary. debug-flags should be computed by
adding the numbers of the desired features from the following
list:
2 - Debug block relocations
4 - Debug inode relocations
8 - Debug moving the inode table
16 - Print timing information
32 - Debug minimum file system size (-M) calculation
-f Forces resize2fs to proceed with the file system resize opera-
tion, overriding some safety checks which resize2fs normally en-
forces.
-F Flush the file system device's buffer caches before beginning.
Only really useful for doing resize2fs time trials.
-M Shrink the file system to minimize its size as much as possible,
given the files stored in the file system.
-p Print out percentage completion bars for each resize2fs phase
during an offline (non-trivial) resize operation, so that the
user can keep track of what the program is doing. (For very fast
resize operations, no progress bars may be displayed.)
-P Print an estimate of the number of file system blocks in the file
system if it is shrunk using resize2fs's -M option and then exit.
-s Turns off the 64bit feature and frees blocks that are no longer
in use.
-S RAID-stride
The resize2fs program will heuristically determine the RAID
stride that was specified when the file system was created. This
option allows the user to explicitly specify a RAID stride set-
ting to be used by resize2fs instead.
-z undo_file
Before overwriting a file system block, write the old contents of
the block to an undo file. This undo file can be used with
e2undo(8) to restore the old contents of the file system should
something go wrong. If the empty string is passed as the
undo_file argument, the undo file will be written to a file named
resize2fs-device.e2undo in the directory specified via the
E2FSPROGS_UNDO_DIR environment variable.
WARNING: The undo file cannot be used to recover from a power or
system crash.
KNOWN BUGS
The minimum size of the file system as estimated by resize2fs may be in-
correct, especially for file systems with 1k and 2k blocksizes.
AUTHOR
resize2fs was written by Theodore Ts'o <tytso@mit.edu>.
COPYRIGHT
Resize2fs is Copyright 1998 by Theodore Ts'o and PowerQuest, Inc. All
rights reserved. As of April, 2000 Resize2fs may be redistributed under
the terms of the GPL.
SEE ALSO
fdisk(8), e2fsck(8), mke2fs(8), lvm(8), lvextend(8)
E2fsprogs version 1.47.2 January 2025 RESIZE2FS(8)
Generated by dwww version 1.16 on Fri Dec 12 02:00:47 CET 2025.