reboot(2) System Calls Manual reboot(2)
NAME
reboot - reboot or enable/disable Ctrl-Alt-Del
LIBRARY
Standard C library (libc, -lc)
SYNOPSIS
/* Since Linux 2.1.30 there are symbolic names LINUX_REBOOT_*
for the constants and a fourth argument to the call: */
#include <linux/reboot.h> /* Definition of LINUX_REBOOT_* constants */
#include <sys/syscall.h> /* Definition of SYS_* constants */
#include <unistd.h>
int syscall(SYS_reboot, int magic, int magic2, int op, void *arg);
/* Under glibc and most alternative libc's (including uclibc, dietlibc,
musl and a few others), some of the constants involved have gotten
symbolic names RB_*, and the library call is a 1-argument
wrapper around the system call: */
#include <sys/reboot.h> /* Definition of RB_* constants */
#include <unistd.h>
int reboot(int op);
DESCRIPTION
The reboot() call reboots the system, or enables/disables the reboot
keystroke (abbreviated CAD, since the default is Ctrl-Alt-Delete; it can
be changed using loadkeys(1)).
This system call fails (with the error EINVAL) unless magic equals
LINUX_REBOOT_MAGIC1 (that is, 0xfee1dead) and magic2 equals LINUX_RE-
BOOT_MAGIC2 (that is, 0x28121969). However, since Linux 2.1.17 also
LINUX_REBOOT_MAGIC2A (that is, 0x05121996) and since Linux 2.1.97 also
LINUX_REBOOT_MAGIC2B (that is, 0x16041998) and since Linux 2.5.71 also
LINUX_REBOOT_MAGIC2C (that is, 0x20112000) are permitted as values for
magic2. (The hexadecimal values of these constants are meaningful.)
The op argument can have the following values:
LINUX_REBOOT_CMD_CAD_OFF
(RB_DISABLE_CAD, 0). CAD is disabled. This means that the CAD
keystroke will cause a SIGINT signal to be sent to init (process
1), whereupon this process may decide upon a proper action
(maybe: kill all processes, sync, reboot).
LINUX_REBOOT_CMD_CAD_ON
(RB_ENABLE_CAD, 0x89abcdef). CAD is enabled. This means that
the CAD keystroke will immediately cause the action associated
with LINUX_REBOOT_CMD_RESTART.
LINUX_REBOOT_CMD_HALT
(RB_HALT_SYSTEM, 0xcdef0123; since Linux 1.1.76). The message
"System halted." is printed, and the system is halted. Control
is given to the ROM monitor, if there is one. If not preceded by
a sync(2), data will be lost.
LINUX_REBOOT_CMD_KEXEC
(RB_KEXEC, 0x45584543, since Linux 2.6.13). Execute a kernel
that has been loaded earlier with kexec_load(2). This option is
available only if the kernel was configured with CONFIG_KEXEC.
LINUX_REBOOT_CMD_POWER_OFF
(RB_POWER_OFF, 0x4321fedc; since Linux 2.1.30). The message
"Power down." is printed, the system is stopped, and all power is
removed from the system, if possible. If not preceded by a
sync(2), data will be lost.
LINUX_REBOOT_CMD_RESTART
(RB_AUTOBOOT, 0x1234567). The message "Restarting system." is
printed, and a default restart is performed immediately. If not
preceded by a sync(2), data will be lost.
LINUX_REBOOT_CMD_RESTART2
(0xa1b2c3d4; since Linux 2.1.30). The message "Restarting system
with command '%s'" is printed, and a restart (using the command
string given in arg) is performed immediately. If not preceded
by a sync(2), data will be lost.
LINUX_REBOOT_CMD_SW_SUSPEND
(RB_SW_SUSPEND, 0xd000fce1; since Linux 2.5.18). The system is
suspended (hibernated) to disk. This option is available only if
the kernel was configured with CONFIG_HIBERNATION.
Only the superuser may call reboot().
The precise effect of the above actions depends on the architecture.
For the i386 architecture, the additional argument does not do anything
at present (2.1.122), but the type of reboot can be determined by kernel
command-line arguments ("reboot=...") to be either warm or cold, and ei-
ther hard or through the BIOS.
Behavior inside PID namespaces
Since Linux 3.4, if reboot() is called from a PID namespace other than
the initial PID namespace with one of the op values listed below, it
performs a "reboot" of that namespace: the "init" process of the PID
namespace is immediately terminated, with the effects described in
pid_namespaces(7).
The values that can be supplied in op when calling reboot() in this case
are as follows:
LINUX_REBOOT_CMD_RESTART
LINUX_REBOOT_CMD_RESTART2
The "init" process is terminated, and wait(2) in the parent
process reports that the child was killed with a SIGHUP signal.
LINUX_REBOOT_CMD_POWER_OFF
LINUX_REBOOT_CMD_HALT
The "init" process is terminated, and wait(2) in the parent
process reports that the child was killed with a SIGINT signal.
For the other op values, reboot() returns -1 and errno is set to EINVAL.
RETURN VALUE
For the values of op that stop or restart the system, a successful call
to reboot() does not return. For the other op values, zero is returned
on success. In all cases, -1 is returned on failure, and errno is set
to indicate the error.
ERRORS
EFAULT Problem with getting user-space data under LINUX_RE-
BOOT_CMD_RESTART2.
EINVAL Bad magic numbers or op.
EPERM The calling process has insufficient privilege to call reboot();
the caller must have the CAP_SYS_BOOT inside its user namespace.
STANDARDS
Linux.
SEE ALSO
systemctl(1), systemd(1), kexec_load(2), sync(2), bootparam(7), capabil-
ities(7), ctrlaltdel(8), halt(8), shutdown(8)
Linux man-pages 6.9.1 2024-05-02 reboot(2)
Generated by dwww version 1.16 on Tue Dec 16 04:26:52 CET 2025.