read(2) System Calls Manual read(2)
NAME
read - read from a file descriptor
LIBRARY
Standard C library (libc, -lc)
SYNOPSIS
#include <unistd.h>
ssize_t read(int fd, void buf[.count], size_t count);
DESCRIPTION
read() attempts to read up to count bytes from file descriptor fd into
the buffer starting at buf.
On files that support seeking, the read operation commences at the file
offset, and the file offset is incremented by the number of bytes read.
If the file offset is at or past the end of file, no bytes are read, and
read() returns zero.
If count is zero, read() may detect the errors described below. In the
absence of any errors, or if read() does not check for errors, a read()
with a count of 0 returns zero and has no other effects.
According to POSIX.1, if count is greater than SSIZE_MAX, the result is
implementation-defined; see NOTES for the upper limit on Linux.
RETURN VALUE
On success, the number of bytes read is returned (zero indicates end of
file), and the file position is advanced by this number. It is not an
error if this number is smaller than the number of bytes requested; this
may happen for example because fewer bytes are actually available right
now (maybe because we were close to end-of-file, or because we are read-
ing from a pipe, or from a terminal), or because read() was interrupted
by a signal. See also NOTES.
On error, -1 is returned, and errno is set to indicate the error. In
this case, it is left unspecified whether the file position (if any)
changes.
ERRORS
EAGAIN The file descriptor fd refers to a file other than a socket and
has been marked nonblocking (O_NONBLOCK), and the read would
block. See open(2) for further details on the O_NONBLOCK flag.
EAGAIN or EWOULDBLOCK
The file descriptor fd refers to a socket and has been marked
nonblocking (O_NONBLOCK), and the read would block. POSIX.1-2001
allows either error to be returned for this case, and does not
require these constants to have the same value, so a portable ap-
plication should check for both possibilities.
EBADF fd is not a valid file descriptor or is not open for reading.
EFAULT buf is outside your accessible address space.
EINTR The call was interrupted by a signal before any data was read;
see signal(7).
EINVAL fd is attached to an object which is unsuitable for reading; or
the file was opened with the O_DIRECT flag, and either the ad-
dress specified in buf, the value specified in count, or the file
offset is not suitably aligned.
EINVAL fd was created via a call to timerfd_create(2) and the wrong size
buffer was given to read(); see timerfd_create(2) for further in-
formation.
EIO I/O error. This will happen for example when the process is in a
background process group, tries to read from its controlling ter-
minal, and either it is ignoring or blocking SIGTTIN or its
process group is orphaned. It may also occur when there is a
low-level I/O error while reading from a disk or tape. A further
possible cause of EIO on networked filesystems is when an advi-
sory lock had been taken out on the file descriptor and this lock
has been lost. See the Lost locks section of fcntl(2) for fur-
ther details.
EISDIR fd refers to a directory.
Other errors may occur, depending on the object connected to fd.
STANDARDS
POSIX.1-2008.
HISTORY
SVr4, 4.3BSD, POSIX.1-2001.
NOTES
On Linux, read() (and similar system calls) will transfer at most
0x7ffff000 (2,147,479,552) bytes, returning the number of bytes actually
transferred. (This is true on both 32-bit and 64-bit systems.)
On NFS filesystems, reading small amounts of data will update the time-
stamp only the first time, subsequent calls may not do so. This is
caused by client side attribute caching, because most if not all NFS
clients leave st_atime (last file access time) updates to the server,
and client side reads satisfied from the client's cache will not cause
st_atime updates on the server as there are no server-side reads. UNIX
semantics can be obtained by disabling client-side attribute caching,
but in most situations this will substantially increase server load and
decrease performance.
BUGS
According to POSIX.1-2008/SUSv4 Section XSI 2.9.7 ("Thread Interactions
with Regular File Operations"):
All of the following functions shall be atomic with respect to each
other in the effects specified in POSIX.1-2008 when they operate on
regular files or symbolic links: ...
Among the APIs subsequently listed are read() and readv(2). And among
the effects that should be atomic across threads (and processes) are up-
dates of the file offset. However, before Linux 3.14, this was not the
case: if two processes that share an open file description (see open(2))
perform a read() (or readv(2)) at the same time, then the I/O operations
were not atomic with respect to updating the file offset, with the re-
sult that the reads in the two processes might (incorrectly) overlap in
the blocks of data that they obtained. This problem was fixed in Linux
3.14.
SEE ALSO
close(2), fcntl(2), ioctl(2), lseek(2), open(2), pread(2), readdir(2),
readlink(2), readv(2), select(2), write(2), fread(3)
Linux man-pages 6.9.1 2024-05-02 read(2)
Generated by dwww version 1.16 on Tue Dec 16 03:57:22 CET 2025.