Ppmtompeg User Manual(1) General Commands Manual Ppmtompeg User Manual(1)
NAME
ppmtompeg - encode an MPEG-1 bitstream
SYNOPSIS
ppmtompeg [options] parameter-file
DESCRIPTION
This program is part of Netpbm(1).
ppmtompeg produces an MPEG-1 video stream. MPEG-1 is the first great
video compression method, and is what is used in Video CDs (VCD). ppm-
tompeg originated in the year 1995. DVD uses a more advanced method,
MPEG-2. There is an even newer method called MPEG-4 which is also
called Divx. I don't know where one finds that used.
There's technically a difference between a compression method for video
and an actual file (stream) format for a movie, and I don't know if it
can be validly said that the format of the stream ppmtompeg produces is
MPEG-1.
Mencoder from the ]8;;http://www.mplayerhq.hu\Mplayer package]8;;\ is probably superior for most video
format generation needs, if for no other reason than that it is more
popular.
The programming library ]8;;http://pm2v.free.fr\PM2V]8;;\ generates MPEG-2 streams.
Use ]8;;http://www.mplayerhq.hu\Mplayer]8;;\ (not part of Netpbm) to do the reverse conversion: to cre-
ate a series of PNM files from an MPEG stream.
param_file is a parameter file which includes a list of input files and
other parameters. The file is described in detail below.
To understand this program, you need to understand something about the
complex MPEG-1 format. One source of information about this standard
format is the section Introduction to MPEG in the ]8;;http://www.faqs.org/faqs/compression-faq/\Compression FAQ]8;;\ .
OPTIONS
The -gop, -combine_gops, -frames, and -combine_frames options are all
mutually exclusive.
-stat stat_file
This option causes ppmtompeg to append the statistics that it
write to Standard Output to the file stat_file as well. The sta-
tistics use the following abbreviations: bits per block (bpb),
bits per frame (bpf), seconds per frame (spf), and bits per sec-
ond (bps).
These statistics include how many I, P, and B frames there were,
and information about compression and quality.
-quiet num_seconds
causes ppmtompeg not to report remaining time more often than
every num_seconds seconds (unless the time estimate rises, which
will happen near the beginning of the run). A negative value
tells ppmtompeg not to report at all. 0 is the default (reports
once after each frame). Note that the time remaining is an esti-
mate and does not take into account time to read in frames.
-realquiet
causes ppmtompeg to run silently, with the only screen output
being errors. Particularly useful when reading input from stdin.
The equivalent of the -quiet common option of most other Netpbm
programs.
-no_frame_summary
This option prevents ppmtompeg from printing a summary line for
each frame
-float_dct
forces ppmtompeg to use a more accurate, yet more computation-
ally expensive version of the DCT.
-gop gop_num
causes ppmtompeg to encode only the numbered GOP (first GOP is
0). The parameter file is the same as for normal usage. The
output file will be the normal output file with the suffix
.gop.gop_num. ppmtompeg does not output any sequence informa-
tion.
-combine_gops
causes ppmtompeg simply to combine some GOP files into a single
MPEG output stream. ppmtompeg inserts a sequence header and
trailer. In this case, the parameter file needs only to contain
the SIZE value, an output file, and perhaps a list of input GOP
files (see below).
If you don't supply a list of input GOP files is used, then ppm-
tompeg assumes you're using the same parameter file you used when
you created the input (with the -gop option) and calculates the
corresponding gop filenames itself. If this is not the case, you
can specify input GOP files in the same manner as normal input
files -- except instead of using INPUT_DIR, INPUT, and END_INPUT,
use GOP_INPUT_DIR, GOP_INPUT, and GOP_END_INPUT. If no input GOP
files are specified, then the default is to use the output file
name with suffix .gop.gop_num, with gop_num starting from 0, as
the input files.
Thus, unless you're mixing and matching GOP files from different
sources, you can simply use the same parameter file for creating
the GOP files (-gop) and for later turning them into an MPEG
stream (-combine_gops).
-frames first_frame last_frame
This option causes ppmtompeg to encode only the frames numbered
first_frame to last_frame, inclusive. The parameter file is the
same as for normal usage. The output will be placed in separate
files, one per frame, with the file names being the normal output
file name with the suffix .frame.frame_num. No GOP header infor-
mation is output. (Thus, the parameter file need not include the
GOP_SIZE value)
Use ppmtompeg -combine_frames to combine these frames later into
an MPEG stream.
-combine_frames
This option causes ppmtompeg simply to combine some individual
MPEG frames (such as you might have created with an earlier run
of ppmtompeg -frames) into a single MPEG stream. Sequence and
GOP headers are inserted appropriately. In this case, the para-
meter file needs to contain only the SIZE value, the GOP_SIZE
value, an output file, and perhaps a list of frame files (see be-
low).
The parameter file may specify input frame files in the same man-
ner as normal input files -- except instead of using INPUT_DIR,
INPUT, and END_INPUT, use FRAME_INPUT_DIR, FRAME_INPUT, and
FRAME_END_INPUT. If no input frame files are specified, then the
default is to use the output file name with suffix
.frame.frame_num, with frame_num starting from 0, as the input
files.
-nice This option causes ppmtompeg to run any remote processes
"nicely," i.e. at low priority. (This is relevant only if you
are running ppmtompeg in parallel mode. Otherwise, there are no
remote processes). See 'man nice.'
-max_machines num_machines
This option causes ppmtompeg to use no more than num_machines ma-
chines as slaves for use in parallel encoding.
-snr This option causes ppmtompeg to include the signal-to-noise ratio
in the reported statistics. Prints SNR (Y U V) and peak SNR (Y U
V) for each frame. In summary, prints averages of luminance only
(Y). SNR is defined as 10*log(variance of original/variance of
error). Peak SNR is defined as 20*log(255/RMSE). Note that ppm-
tompeg runs a little slower when you use this option.
-mse This option causes ppmtompeg to report the mean squared error per
block. It also automatically reports the quality of the images,
so there is no need to specify -snr then.
-bit_rate_info rate_file
This option makes ppmtompeg write bit rate information into the
file rate_file. Bit rate information is bits per frame, and also
bits per I-frame-to-I-frame.
-mv_histogram
This option causes ppmtompeg to print a histogram of the motion
vectors as part of statistics. There are three histograms -- one
for P frame, one for forward B frame, and one for backward B
frame motion vectors.
The output is in the form of a matrix, each entry corresponding
to one motion vector in the search window. The center of the ma-
trix represents (0,0) motion vectors.
-debug_sockets
This option causes ppmtompeg to print to Standard Output messages
that narrate the communication between the machines when you run
ppmtompeg in ]8;;#parallel\parallel mode]8;;\ .
-debug_machines
This option causes ppmtompeg to print to Standard Output messages
that narrate the progress of the conversion on the various ma-
chines when you run ppmtompeg in ]8;;#parallel\parallel mode]8;;\ .
PARAMETER FILE
The parameter file must contain the following lines (except when using
the -combine_gops or -combine_frames options):
PATTERN pattern
This statement specifies the pattern (sequence) of I frames, P
frames, and B frames. pattern is just a sequence of the letters
I, P, and B with nothing between. Example:
PATTERN IBBPBBPBBPBBPBB
</pre>
See
]8;;#ipb\I Frames, P Frames, B Frames]8;;\
.
OUTPUT output file
This names the file where the output MPEG stream goes.
INPUT_DIR directory
This statement tells where the input images (frames) come from.
If each frame is in a separate file, directory is the directory
where they all are. You may use . to refer to the current
directory. A null directory refers to the root directory of the
system file tree.
To have ppmtompeg read all the frames serially from Standard
Input, specify
INPUT_DIR stdin
INPUT This line must be followed by a list of the input files (in dis-
play order) and then the line END_INPUT.
There are three types of lines between INPUT and END_INPUT.
First, a line may simply be the name of an input file. Second,
the line may be of the form single_star_expr [x-y]. sin-
gle_star_expr can have a single * in it. It is replaced by all
the numbers between x and y inclusive. So, for example, the line
tennis*.ppm [12-15] refers to the files tennis12.ppm, ten-
nis13.ppm, tennis14.ppm, tennis15.ppm.
Uniform zero-padding occurs, as well. For example, the line
football.*.ppm [001-130] refers to the files football.001.ppm,
football.002.ppm, ..., football.009.ppm, football.010.ppm, ...,
football.130.ppm.
The third type of line is: single_star_expr [x-y+s], where the
line is treated exactly as above, except that we skip by s.
Thus, the line football.*.ppm [001-130+4] refers to the files
football.001.ppm, football.005.ppm, football.009.ppm, foot-
ball.013.ppm, etc.
Furthermore, a line may specify a shell command to execute to
generate lines to be interpreted as described above, as if those
lines were in the parameter file instead. Use back ticks, like
in the Bourne Shell, like this:
`cat myfilelist`
If input is from Standard Input (per the INPUT_DIR statement),
ppmtompeg ignores the INPUT/END_INPUT block, but it still must be
present.
BASE_FILE_FORMAT {PPM | PNM | YUV |
JPEG | JMOVIE} ppmtompeg must convert all input files to one
of the following formats as a first step of processing: PNM, YUV,
JPEG(v4), or JMOVIE. (The conversion may be trivial if your in-
put files are already in one of these formats). This line speci-
fies which of the four formats. PPM is actually a subset of PNM.
The separate specification is allowed for backward compatibility.
Use PNM instead of PPM in new applications.
INPUT_CONVERT conversion_command
You must specify how to convert a file to the base file format.
If no conversion is necessary, then you would just say:
INPUT_CONVERT *
Otherwise, conversion_command is a shell command that causes an
image in the format your specified with BASE_FILE_FORMAT to be
written to Standard Output. ppmtompeg executes the command once
for each line between INPUT and END_INPUT (which is normally, but
not necessarily, a file name). In the conversion command, ppm-
tompeg replaces each '*' with the contents of that line.
If you had a bunch of gif files, you might say:
INPUT_CONVERT giftopnm *
If you have a bunch of separate a.Y, a.U, and a.V files
(where
the U and V have already been subsampled), then you might
say:
INPUT_CONVERT cat *.Y *.U *.V
Input conversion is not allowed with input from stdin, so use
INPUT_CONVERT *
as described above.
SIZE widthxheight
width and height are the width and height of each frame in pix-
els.
When ppmtompeg can get this information from the input image
files, it ignores the SIZE parameter and you may omit it.
When the image files are in YUV format, the files don't contain
dimension information, so SIZE is required.
When ppmtompeg is running in parallel mode, not all of the
processes in the network have access to the image files, so SIZE
is required and must give the same dimensions as the input image
files.
YUV_SIZE widthxheight
This is an obsolete synonym of SIZE.
YUV_FORMAT {ABEKAS | PHILLIPS | UCB |
EYUV | pattern} This is meaningful only
when BASE_FILE_FORMAT specifies YUV format, and then it is re-
quired. It specifies the sub-format of the YUV class.
GOP_SIZE n
n is the number of frames in a Group of Pictures. Except that
because a GOP must start with an I frame, ppmtompeg makes a GOP
as much longer than n as it has to to make the next GOP start
with an I frame.
Normally, it makes sense to make your GOP size a multiple of your
pattern length (the latter is determined by the PATTERN parameter
file statement).
See ]8;;#gop\Group Of Pictures]8;;\ .
SLICES_PER_FRAME n
n is roughly the number of slices per frame. Note, at least one
MPEG player may complain if slices do not start at the left side
of an image. To ensure this does not happen, make sure the num-
ber of rows is divisible by SLICES_PER_FRAME.
PIXEL {FULL | HALF}
use half-pixel motion vectors, or just full-pixel ones It is usu-
ally important that you use half-pixel motion vectors, because it
results in both better quality and better compression.
RANGE n
Use a search range of n pixels in each of the four directions
from a subject pixel. (So the search window is a square n*2 pix-
els on a side).
PSEARCH_ALG {EXHAUSTIVE | TWOLEVEL |
SUBSAMPLE | LOGARITHMIC} This statement tells ppmtompeg what
kind of search
technique (algorithm) to use for P frames. You select the
desired
combination of speed and compression. EXHAUSTIVE gives the
best compression, but LOGARITHMIC is the fastest.
TWOLEVEL is an exhaustive full-pixel search, followed by a
local half- pixel search around the best full-pixel vector
(the
PIXEL option is ignored for this search technique).
BSEARCH_ALG {SIMPLE | CROSS2 | EXHAUSTIVE}
This statement tells ppmtompeg what kind of search
technique (algorithm) to use for B frames. SIMPLE means
find best forward and backward vectors, then interpolate.
CROSS2 means find those two vectors, then see what backward
vector best matches the best forward vector, and vice versa.
EXHAUSTIVE does an n-squared search and is
extremely slow in relation to the others (CROSS2
is about half as fast as SIMPLE).
IQSCALE n
Use n as the qscale for I frames.
See ]8;;#qscale\Qscale]8;;\ .
PQSCALE n
Use n as the qscale for P frames.
See ]8;;#qscale\Qscale]8;;\ .
BQSCALE n
Use n as the qscale for B frames.
See ]8;;#qscale\Qscale]8;;\ .
REFERENCE_FRAME {ORIGINAL | DECODED}
This statement determines whether ppmtompeg uses the original im-
ages or the decoded images when computing motion vectors. Using
decoded images is more accurate and should increase the playback
quality of the output, but it makes the encoding take longer and
seems to give worse compression. It also causes some complica-
tions with parallel encoding. (see the section on parallel encod-
ing). One thing you can do as a trade-off is select ORIGINAL
here, and lower the qscale (see QSCALE if the quality is not good
enough.
Original or Decoded? (Normalized)
────────────────────────────────────────────────────────────────────
Reference Compression Speed Quality I Quality P Quality B
Decoded 1000 1000 1000 969 919
Original 885 1373 1000 912 884
The following lines are optional:
FORCE_ENCODE_LAST_FRAME
This statement is obsolete. It does nothing.
Before Netpbm 10.26 (January 2005), ppmtompeg would drop trailing
B frames from your movie, since a movie can't end with a B frame.
(See ]8;;#ipb\I Frames, P Frames, B Frames]8;;\ .) You would have to specify
FORCE_ENCODE_LAST_FRAME to stop that from happening and get the
same function that ppmtompeg has today.
NIQTABLE
This statement specifies a custom non-intra quantization table.
If you don't specify this statement, ppmtompeg uses a default
non-intra quantization table.
The 8 lines immediately following NIQTABLE specify the quantiza-
tion table. Each line defines a table row and consists of 8 in-
tegers, whitespace-delimited, which define the table columns.
IQTABLE
This is analogous to NIQTABLE, but for the intra quantization ta-
ble.
ASPECT_RATIO ratio
This statement specifies the aspect ratio for ppmtompeg to spec-
ify in the MPEG output. I'm not sure what this is used for.
ratio must be 1.0, 0.6735, 0.7031, 0.7615, 0.8055, 0.8437,
0.8935, 0.9157, 0.9815, 1.0255, 1.0695, 1.0950, 1.1575, or
1.2015.
FRAME_RATE rate
This specifies the frame rate for ppmtompeg to specify in the
MPEG output. Some players use this value to determine the play-
back rate.
rate must be 23.976, 24, 25, 29.97, 30, 50, 59.94, or 60.
BIT_RATE rate
This specifies the bit rate for Constant Bit Rate (CBR) encoding.
rate must be an integer.
BUFFER_SIZE size
This specifies the value ppmtompeg is to specify in the MPEG out-
put for the Video Buffering Verifier (VBV) buffer size needed to
decode the sequence.
A Video Verifying Buffer is a buffer in which a decoder keeps the
decoded bits in order to match the uneven speed of the decoding
with the required constant playback speed.
As ppmtompeg encodes the image, it simulates the decoding process
in terms of how many bits would be in the VBV as each frame gets
decoded, assuming a VBV of the size you indicate.
If you specify the WARN_VBV_UNDERFLOW statement, ppmtompeg issues
a warning each time the simulation underflows the buffer, which
suggests that an underflow would occur on playback, which sug-
gests the buffer is too small.
If you specify the WARN_VBV_OVERFLOW statement, ppmtompeg issues
a warning each time the simulation overflows the buffer, which
suggests that an overflow would occur on playback, which suggests
the buffer is too small.
WARN_VBV_UNDERFLOW
WARN_VBV_OVERFLOW
See BUFFER_SIZE.
These options were new in Netpbm 10.26 (January 2005). Before
that, ppmtompeg issued the warnings always.
The following statements apply only to parallel operation:
PARALLEL
This statement, paired with END PARALLEL, is what causes ppmtom-
peg to operate in parallel mode. See ]8;;#parallel\Parallel Operation]8;;\ .
END PARALLEL
This goes with PARALLEL.
PARALLEL_TEST_FRAMES n
The master starts off by measuring each slave's speed. It does
this by giving each slave n frames to encode and noting how long
the slave takes to finish. These are not just test frames,
though -- they're real frames and the results become part of the
output. ppmtompeg is old and measures time in undivided seconds,
so to get useful timings, specify enough frames that it will take
at least 5 seconds to process them. The default is 10.
If you specify FORCE_I_ALIGN, ppmtompeg will increase the test
frames value enough to maintain the alignment.
If there aren't enough frames for every slave to have the indi-
cated number of test frames, ppmtompeg will give some slaves
fewer.
PARALLEL_TIME_CHUNKS t
When you specify this statement, the master attempts to feed work
to the slaves in chunks that take t seconds to process. It uses
the speed measurement it made when it started up (see PARAL-
LEL_TEST_FRAMES) to decide how many frames to put in the chunk.
This statement obviously doesn't affect the first batch of work
sent to each slave, which is the one used to measure the slave's
speed.
Smaller values of t increase communication, but improve load bal-
ancing. The default is 30 seconds.
You may specify only one of PARALLEL_TIME_CHUNKS, PARAL-
LEL_CHUNK_TAPER, and PARALLEL_PERFECT. PARALLEL_CHUNK_TAPER is
usually best.
PARALLEL_CHUNK_TAPER
When you specify this statement, the master distributes work like
with PARALLEL_TIME_CHUNKS, except that the master chooses the
number of seconds for the chunks. It starts with a large number
and, as it gets closer to finishing the job, reduces it. That
way, it reduces scheduling overhead when precise scheduling isn't
helpful, but still prevents a slave from finishing early after
all the work has already been handed out to the other slaves, and
then sitting idle while there's still work to do.
You may specify only one of PARALLEL_TIME_CHUNKS, PARAL-
LEL_CHUNK_TAPER, and PARALLEL_PERFECT. PARALLEL_CHUNK_TAPER is
usually best.
PARALLEL_PERFECT
If this statement is present, ppmtompeg schedules on the assump-
tion that each machine is about the same speed. The master will
simply divide up the frames evenly between the slaves -- each
slave gets the same number of frames. If some slaves are faster
than others, they will finish first and remain idle while the
slower slaves continue.
This has the advantage of minimal scheduling overhead. Where
slaves have different speeds, though, it makes inefficient use of
the fast ones. Where slaves are the same speed, it also has the
disadvantage that they all finish at the same time and feed their
output to the single Combine Server in a burst, which makes less
efficient use of the Combine Server and thus can increase the to-
tal elapsed time.
You may specify only one of PARALLEL_TIME_CHUNKS, PARAL-
LEL_CHUNK_TAPER, and PARALLEL_PERFECT. PARALLEL_CHUNK_TAPER is
usually best.
RSH remote_shell_command
ppmtompeg executes the shell command remote_shell_command to
start a process on another machine. The default command is rsh,
and whatever command you specify must have compatible semantics.
ssh is usually compatible. The command ppmtompeg uses is one
like this: ssh remote.host.com -l username shellcommand.
Be sure to set up .rhosts files or SSH key authorizations where
needed. Otherwise, you'll have to type in passwords.
On some HP machines, rsh is the restricted shell, and you want to
specify remsh.
FORCE_I_ALIGN
This statement forces each slave to encode a chunk of frames
which is a multiple of the pattern length (see PATTERN). Since
the first frame in any pattern is an I frame, this forces each
chunk encoded by a slave to begin with an I frame.
This document used to say there was an argument to FORCE_I_ALIGN
which was the number of frames ppmtompeg would use (and was re-
quired to be a multiple of the pattern length). But ppmtompeg
has apparently always ignored that argument, and it does now.
KEEP_TEMP_FILES
This statement causes ppmtompeg not to delete the temporary files
it uses to transmit encoded frames to the combine server. This
means you will be left with a file for each frame, the same as
you would get with the -frames option.
This is mostly useful for debugging.
This works only if you're using a shared filesystem to communi-
cate between the servers.
This option was new in Netpbm 10.26 (January 2005).
Parameter File Notes
If you use the -combine_gops option, then you need to specify only the
SIZE and OUTPUT values in the parameter file. In addition, the parame-
ter file may specify input GOP files in the same manner as normal input
files -- except instead of using INPUT_DIR, INPUT, and END_INPUT, use
GOP_INPUT_DIR, GOP_INPUT, and GOP_END_INPUT. If you specify no input
GOP files, then ppmtompeg uses by default the output file name with suf-
fix .gop.gop_num, with gop_num starting from 0, as the input files.
If you use the -combine_frames option, then you need to specify only the
SIZE, GOP_SIZE, and OUTPUT values in the parameter file. In addition,
the parameter file may specify input frame files in the same manner as
normal input files -- except instead of using INPUT_DIR, INPUT, and
END_INPUT, use FRAME_INPUT_DIR, FRAME_INPUT, and FRAME_END_INPUT. If no
input frame files are specified, then the default is to use the output
file name with suffix .frame.frame_num, with frame_num starting from 0,
as the input files.
Any number of spaces and tabs may come between each option and value.
Lines beginning with # are ignored. Any other lines are ignored except
for those between INPUT and END_INPUT. This allows you to use the same
parameter file for normal usage and for -combine_gops and -com-
bine_frames.
The file format is case-sensitive so all keywords should be in upper
case.
The statements may appear in any order, except that the order within a
block statement (such as INPUT ... END INPUT) is significant.
ppmtompeg is prepared to handle up to 16 B frames between reference
frames when encoding with input from stdin. (To build a modified ppm-
tompeg with a higher limit, change the constant B_FRAME_RUN in frame.c
and recompile).
GENERAL USAGE INFORMATION
Qscale
The quantization scale values (qscale) give a trade-off between quality
and compression. Using different Qscale values has very little effect
on speed. The qscale values can be set separately for I, P, and B
frames.
You select the qscale values with the IQSCALE, PQSCALE, and BSCALE para-
meter file statements.
A qscale value is an integer from 1 to 31. Larger numbers give better
compression, but worse quality. In the following, the quality numbers
are peak signal-to-noise ratio, defined as: signal-to-noise formula
where MSE is the mean squared error.
Flower garden tests:
Qscale vs Quality
────────────────────────────────────────
Qscale I Frames P Frames B Frames
1 43.2 46.3 46.5
6 32.6 34.6 34.3
11 28.6 29.5 30.0
16 26.3 26.8 28.6
21 24.7 25.0 27.9
26 23.5 23.9 27.5
31 22.6 23.0 27.3
Qscale vs Compression
────────────────────────────────────────
Qscale I Frames P Frames B Frames
1 2 2 2
6 7 10 15
11 11 18 43
16 15 29 97
21 19 41 173
26 24 56 256
31 28 73 330
Search Techniques
There are several different motion vector search techniques available.
There are different techniques available for P frame search and B frame
search. Using different search techniques present little difference in
quality, but a large difference in compression and speed.
There are 4 types of P frame search: Exhaustive, TwoLevel, SubSample,
and Logarithmic.
There are 3 types of B frame search: Exhaustive, Cross2, and Simple.
The recommended search techniques are TwoLevel and Logarithmic for P
frame search, and Cross2 and Simple for B frame search. Here are some
numbers comparing the different search methods:
P frame Motion Vector Search (Normalized)
─────────────────────────────────────────────────────────────────────
Technique Compression 1 Speed 2 Quality 3
⟨#smallbetter⟩ ⟨#largefaster⟩ ⟨#largebetter⟩
Exhaustive 1000 1000 1000
SubSample 1008 2456 1000
TwoLevel 1009 3237 1000
Logarithmic 1085 8229 998
B frame Motion Vector Search (Normalized)
────────────────────────────────────────────────────────────────────
Technique Compression 1 Speed 2 Quality 3
⟨#smallbetter⟩ ⟨#largefaster⟩ ⟨#largebetter⟩
Exhaustive 1000 1000 1000
Cross2 975 1000 996
Simple 938 1765 991
1Smaller numbers are better compression.
2Larger numbers mean faster execution.
3Larger numbers mean better quality.
For some reason, Simple seems to give better compression, but it depends
on the image sequence.
Select the search techniques with the PSEARCH_ALG and BSEARCH_ALG para-
meter file statements.
Group Of Pictures (GOP)
A Group of Pictures (GOP) is a roughly independently decodable sequence
of frames. An MPEG video stream is made of one or more GOP's. You may
specify how many frames should be in each GOP with the GOP_SIZE parame-
ter file statement. A GOP always starts with an I frame.
Instead of encoding an entire sequence, you can encode a single GOP. To
do this, use the -gop command option. You can later join the resulting
GOP files at any time by running ppmtompeg with the -combine_gops com-
mand option.
Slices
A slice is an independently decodable unit in a frame. It can be as
small as one macroblock, or it can be as big as the entire frame. Bar-
ring transmission error, adding slices does not change quality or speed;
the only effect is slightly worse compression. More slices are used for
noisy transmission so that errors are more recoverable. Since usually
errors are not such a problem, we usually just use one slice per frame.
Control the slice size with the SLICES_PER_FRAME parameter file state-
ment.
Some MPEG playback systems require that each slice consist of whole rows
of macroblocks. If you are encoding for this kind of player, if the
height of the image is H pixels, then you should set the
SLICES_PER_FRAME to some number which divides H/16. For example, if the
image is 240 pixels (15 macroblocks) high, then you should use only 15,
5, 3, or 1 slices per frame.
Note: these MPEG playback systems are really wrong, since the MPEG stan-
dard says this doesn't have to be so.
Search Window
The search window is the window in which ppmtompeg searches for motion
vectors. The window is a square. You can specify the size of the
square, and whether to allow half-pixel motion vectors or not, with the
RANGE and PIXEL parameter file statements.
I Frames, P Frames, B Frames
In MPEG-1, a movie is represented as a sequence of MPEG frames, each of
which is an I Frame, a P Frame, or a B Frame. Each represents an actual
frame of the movie (don't get confused by the dual use of the word
"frame." A movie frame is a graphical image. An MPEG frame is a set of
data that describes a movie frame).
An I frame ("intra" frame) describes a movie frame in isolation -- with-
out respect to any other frame in the movie. A P frame ("predictive"
frame) describes a movie frame by describing how it differs from the
movie frame described by the latest preceding I or P frame. A B frame
("bidirectional" frame) describes a movie frame by describing how it
differs from the movie frames described by the nearest I or P frame be-
fore and after it.
Note that the first frame of a movie must be described by an I frame
(because there is no previous movie frame) and the last movie frame must
be described by an I or P frame (because there is no subsequent movie
frame).
Beyond that, you can choose which frames are represented by which types.
You specify a pattern, such as IBPBP and ppmtompeg simply repeats it
over and over throughout the movie. The pattern affects speed, quality,
and stream size. Here is a chart which shows some of the trade-offs:
Comparison of I/P/B Frames (Normalized)
────────────────────────────────────
Frame Type Size Speed Quality
I frames 1000 1000 1000
P frames 409 609 969
B frames 72 260 919
(this is with constant qscale)
A standard sequence is IBBPBBPBBPBBPBB.
Select the sequence with the PATTERN parameter file statement.
Since the last MPEG frame cannot be a B frame (see above), if the pat-
tern you specify indicates a B frame for the last movie frame of the
movie, ppmtompeg makes it an I frame instead.
Before Netpbm 10.26 (January 2005), ppmtompeg instead drops the trailing
B frames by default, and you need the FORCE_ENCODE_LAST_FRAME parameter
file statement to make it do this.
The MPEG frames don't appear in the MPEG-1 stream in the same order that
the corresponding movie frames appear in the movie -- the B frames come
after the I and P frames on which they are based. For example, if the
movie is 4 frames that you will represent with the pattern IBBP, the
MPEG-1 stream will start with an I frame describing movie frame 0. The
next frame in the MPEG-1 stream is a P frame describing movie frame 3.
The last two frames in the MPEG-1 stream are B frames describing movie
frames 1 and 2, respectively.
Specifying Input and Output Files
Specify the input frame images with the INPUT_DIR, INPUT, END_INPUT,
BASE_FILE_FORMAT, SIZE, YUV_FORMAT and INPUT_CONVERT parameter file
statements.
Specify the output file with the OUTPUT parameter file statement.
Statistics
ppmtompeg can generate a variety of statistics about the encoding. See
the -stat, -snr, -mv_histogram, -quiet, -no_frame_summary, and
-bit_rate_info options.
PARALLEL OPERATION
You can run ppmtompeg on multiple machines at once, encoding the same
MPEG stream. When you do, the machines are used as shown in the follow-
ing diagram. We call this "parallel mode."
ppmtompeg-par.gif
To do parallel processing, put the statement
PARALLEL
in the parameter file, followed by a listing of the machines, one ma-
chine per line, then
END_PARALLEL
Each of the machine lines must be in one of two forms. If the machine
has filesystem access to the input files, then the line is:
machine user executable
The executable is normally ppmtompeg (you may need to give the complete
path if you've built for different architectures). If the machine does
not have filesystem access to the input files, the line is:
REMOTE machine user executable parameter file
The -max_machines command option limits the number of machines ppmtompeg
will use. If you specify more machines in the parameter file than
-max_machines allows, ppmtompeg uses only the machines listed first.
This is handy if you want to experiment with different amounts of paral-
lelism.
In general, you should use full path file names when describing executa-
bles and parameter files. This includes the parameter file argument on
the original invocation of ppmtompeg.
All file names must be the same on all systems (so if e.g. you're using
an NFS filesystem, you must make sure it is mounted at the same mount-
point on all systems).
Because not all of the processes involved in parallel operation have
easy access to the input files, you must specify the SIZE parameter file
statement when you do parallel operation.
The machine on which you originally invoke ppmtompeg is the master ma-
chine. It hosts a "combine server,", a "decode server," and a number of
"i/o servers," all as separate processes. The other machines in the
network (listed in the parameter file) are slave machines. Each hosts a
single process that continuously requests work from the master and does
it. The slave process does the computation to encode MPEG frames. It
processes frames in batches identified by the master.
The master uses a remote shell command to start a process on a slave ma-
chine. By default, it uses an rsh shell command to do this. But use
the RSH parameter file statement to control this. The shell command the
master executes remotely is ppmtompeg, but with options to indicate that
it is to perform slave functions.
The various machines talk to each other over TCP connections. Each ma-
chine finds and binds to a free TCP port number and tells its partners
the port number. These port numbers are at least 2048.
Use the PARALLEL_TEST_FRAMES, PARALLEL_TIME_CHUNKS, and PARALLEL_PERFECT
parameter file statements to control the way the master divides up work
among the slaves.
Use the -nice command option to cause all slave processes to run
"nicely," i.e. as low priority processes. That way, this substantial
and long-running CPU load will have minimal impact on other, possibly
interactive, users of the systems.
SPEED
Here is a look at ppmtompeg speed, in single-node (not parallel) opera-
tion:
Compression Speed
───────────────────────────────────────
Machine Type Macroblocks per second1
HP 9000/755 280
DEC 3000/400 247
HP 9000/750 191
Sparc 10 104
DEC 5000 68
1A macroblock is a 16x16 pixel square
The measurements in the table are with inputs and outputs via a conven-
tional locally attached filesystem. If you are using a network filesys-
tem over a single 10 MB/s Ethernet, that constrains your speed more than
your CPU speed. In that case, don't expect to get better than 4 or 5
frames per second no matter how fast your CPUs are.
Network speed is even more of a bottleneck when the slaves do not have
filesystem access to the input files -- i.e. you declare them REMOTE.
Where I/O is the bottleneck, size of the input frames can make a big
difference. So YUV input is better than PPM, and JPEG is better than
both.
When you're first trying to get parallel mode working, be sure to use
the -debug_machines option so you can see what's going on. Also, -de-
bug_sockets can help you diagnose communication problems.
AUTHORS
• Kevin Gong - University of California, Berkeley, keving@cs.berke-
ley.edu
• Ketan Patel - University of California, Berkeley, kpa-
tel@cs.berkeley.edu
• Dan Wallach - University of California, Berkeley, dwal-
lach@cs.berkeley.edu
• Darryl Brown - University of California, Berkeley, dar-
ryl@cs.berkeley.edu
• Eugene Hung - University of California, Berkeley, ey-
hung@cs.berkeley.edu
• Steve Smoot - University of California, Berkeley, smoot@cs.berke-
ley.edu
DOCUMENT SOURCE
This manual page was generated by the Netpbm tool 'makeman' from HTML
source. The master documentation is at
http://netpbm.sourceforge.net/doc/ppmtompeg.html
netpbm documentation 23 July 2006 Ppmtompeg User Manual(1)
Generated by dwww version 1.16 on Tue Dec 16 04:56:23 CET 2025.