LVMRAID(7) LVMRAID(7)
NAME
lvmraid — LVM RAID
DESCRIPTION
lvm(8) RAID is a way to create a Logical Volume (LV) that uses multiple
physical devices to improve performance or tolerate device failures. In
LVM, the physical devices are Physical Volumes (PVs) in a single Volume
Group (VG).
How LV data blocks are placed onto PVs is determined by the RAID level.
RAID levels are commonly referred to as 'raid' followed by a number,
e.g. raid1, raid5 or raid6. Selecting a RAID level involves making
tradeoffs among: physical device requirements, fault tolerance, and per-
formance. A description of the RAID levels can be found at
]8;;https://www.snia.org/sites/default/files/SNIA_DDF_Technical_Position_v2.0.pdf\https://www.snia.org/sites/default/files/SNIA_DDF_Technical_Posi-
tion_v2.0.pdf]8;;\
LVM RAID uses both Device Mapper (DM) and Multiple Device (MD) drivers
from the Linux kernel. DM is used to create and manage visible LVM de-
vices, and MD is used to place data on physical devices.
LVM creates hidden LVs (dm devices) layered between the visible LV and
physical devices. LVs in the middle layers are called sub LVs. For LVM
raid, a sub LV pair to store data and metadata (raid superblock and
write intent bitmap) is created per raid image/leg (see lvs command ex-
amples below).
USAGE
To create a RAID LV, use lvcreate and specify an LV type. The LV type
corresponds to a RAID level. The basic RAID levels that can be used
are: raid0, raid1, raid4, raid5, raid6, raid10.
lvcreate --type RaidLevel [OPTIONS] --name Name --size Size VG [PVs]
To display the LV type of an existing LV, run:
lvs -o name,segtype LV
(The LV type is also referred to as "segment type" or "segtype".)
LVs can be created with the following types:
raid0
Also called striping, raid0 spreads LV data across multiple devices in
units of stripe size. This is used to increase performance. LV data
will be lost if any of the devices fail.
lvcreate --type raid0 [--stripes Number --stripesize Size] VG [PVs]
--stripes Number
specifies the Number of devices to spread the LV across.
--stripesize Size
specifies the Size of each stripe in kilobytes. This is the
amount of data that is written to one device before moving to the
next.
PVs specifies the devices to use. If not specified, lvm will choose
Number devices, one for each stripe based on the number of PVs available
or supplied.
raid1
Also called mirroring, raid1 uses multiple devices to duplicate LV data.
The LV data remains available if all but one of the devices fail. The
minimum number of devices (i.e. sub LV pairs) required is 2.
lvcreate --type raid1 [--mirrors Number] VG [PVs]
--mirrors Number
specifies the Number of mirror images in addition to the original
LV image, e.g. --mirrors 1 means there are two images of the
data, the original and one mirror image.
PVs specifies the devices to use. If not specified, lvm will choose
Number devices, one for each image.
raid4
raid4 is a form of striping that uses an extra, first device dedicated
to storing parity blocks. The LV data remains available if one device
fails. The parity is used to recalculate data that is lost from a sin-
gle device. The minimum number of devices required is 3.
lvcreate --type raid4 [--stripes Number --stripesize Size] VG [PVs]
--stripes Number
specifies the Number of devices to use for LV data. This does
not include the extra device lvm adds for storing parity blocks.
A raid4 LV with Number stripes requires Number+1 devices. Number
must be 2 or more.
--stripesize Size
specifies the Size of each stripe in kilobytes. This is the
amount of data that is written to one device before moving to the
next.
PVs specifies the devices to use. If not specified, lvm will choose
Number+1 separate devices.
raid4 is called non-rotating parity because the parity blocks are always
stored on the same device.
raid5
raid5 is a form of striping that uses an extra device for storing parity
blocks. LV data and parity blocks are stored on each device, typically
in a rotating pattern for performance reasons. The LV data remains
available if one device fails. The parity is used to recalculate data
that is lost from a single device. The minimum number of devices re-
quired is 3 (unless converting from 2 legged raid1 to reshape to more
stripes; see reshaping).
lvcreate --type raid5 [--stripes Number --stripesize Size] VG [PVs]
--stripes Number
specifies the Number of devices to use for LV data. This does
not include the extra device lvm adds for storing parity blocks.
A raid5 LV with Number stripes requires Number+1 devices. Number
must be 2 or more.
--stripesize Size
specifies the Size of each stripe in kilobytes. This is the
amount of data that is written to one device before moving to the
next.
PVs specifies the devices to use. If not specified, lvm will choose
Number+1 separate devices.
raid5 is called rotating parity because the parity blocks are placed on
different devices in a round-robin sequence. There are variations of
raid5 with different algorithms for placing the parity blocks. The de-
fault variant is raid5_ls (raid5 left symmetric, which is a rotating
parity 0 with data restart.) See RAID5 VARIANTS below.
raid6
raid6 is a form of striping like raid5, but uses two extra devices for
parity blocks. LV data and parity blocks are stored on each device,
typically in a rotating pattern for performance reasons. The LV data
remains available if up to two devices fail. The parity is used to re-
calculate data that is lost from one or two devices. The minimum number
of devices required is 5.
lvcreate --type raid6 [--stripes Number --stripesize Size] VG [PVs]
--stripes Number
specifies the Number of devices to use for LV data. This does
not include the extra two devices lvm adds for storing parity
blocks. A raid6 LV with Number stripes requires Number+2 de-
vices. Number must be 3 or more.
--stripesize Size
specifies the Size of each stripe in kilobytes. This is the
amount of data that is written to one device before moving to the
next.
PVs specifies the devices to use. If not specified, lvm will choose
Number+2 separate devices.
Like raid5, there are variations of raid6 with different algorithms for
placing the parity blocks. The default variant is raid6_zr (raid6 zero
restart, aka left symmetric, which is a rotating parity 0 with data
restart.) See RAID6 VARIANTS below.
raid10
raid10 is a combination of raid1 and raid0, striping data across mir-
rored devices. LV data remains available if one or more devices remains
in each mirror set. The minimum number of devices required is 4.
lvcreate --type raid10
[--mirrors NumberMirrors]
[--stripes NumberStripes --stripesize Size]
VG [PVs]
--mirrors NumberMirrors
specifies the number of mirror images within each stripe. e.g.
--mirrors 1 means there are two images of the data, the original
and one mirror image.
--stripes NumberStripes
specifies the total number of devices to use in all raid1 images
(not the number of raid1 devices to spread the LV across, even
though that is the effective result). The number of devices in
each raid1 mirror will be NumberStripes/(NumberMirrors+1), e.g.
mirrors 1 and stripes 4 will stripe data across two raid1 mir-
rors, where each mirror contains two devices.
--stripesize Size
specifies the Size of each stripe in kilobytes. This is the
amount of data that is written to one device before moving to the
next.
PVs specifies the devices to use. If not specified, lvm will choose the
necessary devices. Devices are used to create mirrors in the order
listed, e.g. for mirrors 1, stripes 2, listing PV1 PV2 PV3 PV4 results
in mirrors PV1/PV2 and PV3/PV4.
RAID10 is not mirroring on top of stripes, which would be RAID01, which
is less tolerant of device failures.
Configuration Options
There are a number of options in the LVM configuration file that affect
the behavior of RAID LVs. The tunable options are listed below. A de-
tailed description of each can be found in the LVM configuration file
itself.
mirror_segtype_default
raid10_segtype_default
raid_region_size
raid_fault_policy
activation_mode
Monitoring
When a RAID LV is activated the dmeventd(8) process is started to moni-
tor the health of the LV. Various events detected in the kernel can
cause a notification to be sent from device-mapper to the monitoring
process, including device failures and synchronization completion (e.g.
for initialization or scrubbing).
The LVM configuration file contains options that affect how the monitor-
ing process will respond to failure events (e.g. raid_fault_policy). It
is possible to turn on and off monitoring with lvchange, but it is not
recommended to turn this off unless you have a thorough knowledge of the
consequences.
Synchronization
Synchronization is the process that makes all the devices in a RAID LV
consistent with each other.
In a RAID1 LV, all mirror images should have the same data. When a new
mirror image is added, or a mirror image is missing data, then images
need to be synchronized. Data blocks are copied from an existing image
to a new or outdated image to make them match.
In a RAID 4/5/6 LV, parity blocks and data blocks should match based on
the parity calculation. When the devices in a RAID LV change, the data
and parity blocks can become inconsistent and need to be synchronized.
Correct blocks are read, parity is calculated, and recalculated blocks
are written.
The RAID implementation keeps track of which parts of a RAID LV are syn-
chronized. When a RAID LV is first created and activated the first syn-
chronization is called initialization. A pointer stored in the raid
metadata keeps track of the initialization process thus allowing it to
be restarted after a deactivation of the RaidLV or a crash. Any writes
to the RaidLV dirties the respective region of the write intent bitmap
which allow for fast recovery of the regions after a crash. Without
this, the entire LV would need to be synchronized every time it was ac-
tivated.
Automatic synchronization happens when a RAID LV is activated, but it is
usually partial because the bitmaps reduce the areas that are checked.
A full sync becomes necessary when devices in the RAID LV are replaced.
The synchronization status of a RAID LV is reported by the following
command, where "Cpy%Sync" = "100%" means sync is complete:
lvs -a -o name,sync_percent
Scrubbing
Scrubbing is a full scan of the RAID LV requested by a user. Scrubbing
can find problems that are missed by partial synchronization.
Scrubbing assumes that RAID metadata and bitmaps may be inaccurate, so
it verifies all RAID metadata, LV data, and parity blocks. Scrubbing
can find inconsistencies caused by hardware errors or degradation.
These kinds of problems may be undetected by automatic synchronization
which excludes areas outside of the RAID write-intent bitmap.
The command to scrub a RAID LV can operate in two different modes:
lvchange --syncaction check|repair LV
check Check mode is read-only and only detects inconsistent areas in
the RAID LV, it does not correct them.
repair Repair mode checks and writes corrected blocks to synchronize any
inconsistent areas.
Scrubbing can consume a lot of bandwidth and slow down application I/O
on the RAID LV. To control the I/O rate used for scrubbing, use:
--maxrecoveryrate Size[k|UNIT]
Sets the maximum recovery rate for a RAID LV. Size is specified
as an amount per second for each device in the array. If no suf-
fix is given, then KiB/sec/device is used. Setting the recovery
rate to 0 means it will be unbounded.
--minrecoveryrate Size[k|UNIT]
Sets the minimum recovery rate for a RAID LV. Size is specified
as an amount per second for each device in the array. If no suf-
fix is given, then KiB/sec/device is used. Setting the recovery
rate to 0 means it will be unbounded.
To display the current scrubbing in progress on an LV, including the
syncaction mode and percent complete, run:
lvs -a -o name,raid_sync_action,sync_percent
After scrubbing is complete, to display the number of inconsistent
blocks found, run:
lvs -o name,raid_mismatch_count
Also, if mismatches were found, the lvs attr field will display the let-
ter "m" (mismatch) in the 9th position, e.g.
# lvs -o name,vgname,segtype,attr vg/lv
LV VG Type Attr
lv vg raid1 Rwi-a-r-m-
Scrubbing Limitations
The check mode can only report the number of inconsistent blocks, it
cannot report which blocks are inconsistent. This makes it impossible
to know which device has errors, or if the errors affect file system
data, metadata or nothing at all.
The repair mode can make the RAID LV data consistent, but it does not
know which data is correct. The result may be consistent but incorrect
data. When two different blocks of data must be made consistent, it
chooses the block from the device that would be used during RAID ini-
tialization. However, if the PV holding corrupt data is known, lvchange
--rebuild can be used in place of scrubbing to reconstruct the data on
the bad device.
Future developments might include:
Allowing a user to choose the correct version of data during repair.
Using a majority of devices to determine the correct version of data to
use in a 3-way RAID1 or RAID6 LV.
Using a checksumming device to pin-point when and where an error occurs,
allowing it to be rewritten.
SubLVs
An LV is often a combination of other hidden LVs called SubLVs. The
SubLVs either use physical devices, or are built from other SubLVs them-
selves. SubLVs hold LV data blocks, RAID parity blocks, and RAID meta-
data. SubLVs are generally hidden, so the lvs -a option is required to
display them:
lvs -a -o name,segtype,devices
SubLV names begin with the visible LV name, and have an automatic suffix
indicating its role:
• SubLVs holding LV data or parity blocks have the suffix _rim-
age_#.
These SubLVs are sometimes referred to as DataLVs.
• SubLVs holding RAID metadata have the suffix _rmeta_#. RAID
metadata includes superblock information, RAID type, bitmap, and
device health information.
These SubLVs are sometimes referred to as MetaLVs.
SubLVs are an internal implementation detail of LVM. The way they are
used, constructed and named may change.
The following examples show the SubLV arrangement for each of the basic
RAID LV types, using the fewest number of devices allowed for each.
Examples
raid0
Each rimage SubLV holds a portion of LV data. No parity is used. No
RAID metadata is used.
# lvcreate --type raid0 --stripes 2 --name lvr0 ...
# lvs -a -o name,segtype,devices
lvr0 raid0 lvr0_rimage_0(0),lvr0_rimage_1(0)
[lvr0_rimage_0] linear /dev/sda(...)
[lvr0_rimage_1] linear /dev/sdb(...)
raid1
Each rimage SubLV holds a complete copy of LV data. No parity is used.
Each rmeta SubLV holds RAID metadata.
# lvcreate --type raid1 --mirrors 1 --name lvr1 ...
# lvs -a -o name,segtype,devices
lvr1 raid1 lvr1_rimage_0(0),lvr1_rimage_1(0)
[lvr1_rimage_0] linear /dev/sda(...)
[lvr1_rimage_1] linear /dev/sdb(...)
[lvr1_rmeta_0] linear /dev/sda(...)
[lvr1_rmeta_1] linear /dev/sdb(...)
raid4
At least three rimage SubLVs each hold a portion of LV data and one rim-
age SubLV holds parity. Each rmeta SubLV holds RAID metadata.
# lvcreate --type raid4 --stripes 2 --name lvr4 ...
# lvs -a -o name,segtype,devices
lvr4 raid4 lvr4_rimage_0(0),\
lvr4_rimage_1(0),\
lvr4_rimage_2(0)
[lvr4_rimage_0] linear /dev/sda(...)
[lvr4_rimage_1] linear /dev/sdb(...)
[lvr4_rimage_2] linear /dev/sdc(...)
[lvr4_rmeta_0] linear /dev/sda(...)
[lvr4_rmeta_1] linear /dev/sdb(...)
[lvr4_rmeta_2] linear /dev/sdc(...)
raid5
At least three rimage SubLVs each typically hold a portion of LV data
and parity (see section on raid5) Each rmeta SubLV holds RAID metadata.
# lvcreate --type raid5 --stripes 2 --name lvr5 ...
# lvs -a -o name,segtype,devices
lvr5 raid5 lvr5_rimage_0(0),\
lvr5_rimage_1(0),\
lvr5_rimage_2(0)
[lvr5_rimage_0] linear /dev/sda(...)
[lvr5_rimage_1] linear /dev/sdb(...)
[lvr5_rimage_2] linear /dev/sdc(...)
[lvr5_rmeta_0] linear /dev/sda(...)
[lvr5_rmeta_1] linear /dev/sdb(...)
[lvr5_rmeta_2] linear /dev/sdc(...)
raid6
At least five rimage SubLVs each typically hold a portion of LV data and
parity. (see section on raid6) Each rmeta SubLV holds RAID metadata.
# lvcreate --type raid6 --stripes 3 --name lvr6
# lvs -a -o name,segtype,devices
lvr6 raid6 lvr6_rimage_0(0),\
lvr6_rimage_1(0),\
lvr6_rimage_2(0),\
lvr6_rimage_3(0),\
lvr6_rimage_4(0),\
lvr6_rimage_5(0)
[lvr6_rimage_0] linear /dev/sda(...)
[lvr6_rimage_1] linear /dev/sdb(...)
[lvr6_rimage_2] linear /dev/sdc(...)
[lvr6_rimage_3] linear /dev/sdd(...)
[lvr6_rimage_4] linear /dev/sde(...)
[lvr6_rimage_5] linear /dev/sdf(...)
[lvr6_rmeta_0] linear /dev/sda(...)
[lvr6_rmeta_1] linear /dev/sdb(...)
[lvr6_rmeta_2] linear /dev/sdc(...)
[lvr6_rmeta_3] linear /dev/sdd(...)
[lvr6_rmeta_4] linear /dev/sde(...)
[lvr6_rmeta_5] linear /dev/sdf(...)
raid10
At least four rimage SubLVs each hold a portion of LV data. No parity
is used. Each rmeta SubLV holds RAID metadata.
# lvcreate --type raid10 --stripes 2 --mirrors 1 --name lvr10
# lvs -a -o name,segtype,devices
lvr10 raid10 lvr10_rimage_0(0),\
lvr10_rimage_1(0),\
lvr10_rimage_2(0),\
lvr10_rimage_3(0)
[lvr10_rimage_0] linear /dev/sda(...)
[lvr10_rimage_1] linear /dev/sdb(...)
[lvr10_rimage_2] linear /dev/sdc(...)
[lvr10_rimage_3] linear /dev/sdd(...)
[lvr10_rmeta_0] linear /dev/sda(...)
[lvr10_rmeta_1] linear /dev/sdb(...)
[lvr10_rmeta_2] linear /dev/sdc(...)
[lvr10_rmeta_3] linear /dev/sdd(...)
DEVICE FAILURE
Physical devices in a RAID LV can fail or be lost for multiple reasons.
A device could be disconnected, permanently failed, or temporarily dis-
connected. The purpose of RAID LVs (levels 1 and higher) is to continue
operating in a degraded mode, without losing LV data, even after a de-
vice fails. The number of devices that can fail without the loss of LV
data depends on the RAID level:
• RAID0 (striped) LVs cannot tolerate losing any devices. LV data
will be lost if any devices fail.
• RAID1 LVs can tolerate losing all but one device without LV data
loss.
• RAID4 and RAID5 LVs can tolerate losing one device without LV
data loss.
• RAID6 LVs can tolerate losing two devices without LV data loss.
• RAID10 is variable, and depends on which devices are lost. It
stripes across multiple mirror groups with raid1 layout thus it
can tolerate losing all but one device in each of these groups
without LV data loss.
If a RAID LV is missing devices, or has other device-related problems,
lvs reports this in the health_status (and attr) fields:
lvs -o name,lv_health_status
partial
Devices are missing from the LV. This is also indicated by the
letter "p" (partial) in the 9th position of the lvs attr field.
refresh needed
A device was temporarily missing but has returned. The LV needs
to be refreshed to use the device again (which will usually re-
quire partial synchronization). This is also indicated by the
letter "r" (refresh needed) in the 9th position of the lvs attr
field. See Refreshing an LV. This could also indicate a problem
with the device, in which case it should be replaced, see Replac-
ing Devices.
mismatches exist
See Scrubbing.
Most commands will also print a warning if a device is missing, e.g.
WARNING: Device for PV uItL3Z-wBME-DQy0-... not found or rejected ...
This warning will go away if the device returns or is removed from the
VG (see vgreduce --removemissing).
Activating an LV with missing devices
A RAID LV that is missing devices may be activated or not, depending on
the "activation mode" used in lvchange:
lvchange -ay --activationmode complete|degraded|partial LV
complete
The LV is only activated if all devices are present.
degraded
The LV is activated with missing devices if the RAID level can
tolerate the number of missing devices without LV data loss.
partial
The LV is always activated, even if portions of the LV data are
missing because of the missing device(s). This should only be
used to perform extreme recovery or repair operations.
Default activation mode when not specified by the command:
lvm.conf(5) activation/activation_mode
The default value is printed by:
# lvmconfig --type default activation/activation_mode
Replacing Devices
Devices in a RAID LV can be replaced by other devices in the VG. When
replacing devices that are no longer visible on the system, use lvcon-
vert --repair. When replacing devices that are still visible, use lv-
convert --replace. The repair command will attempt to restore the same
number of data LVs that were previously in the LV. The replace option
can be repeated to replace multiple PVs. Replacement devices can be op-
tionally listed with either option.
lvconvert --repair LV [NewPVs]
lvconvert --replace OldPV LV [NewPV]
lvconvert --replace OldPV1 --replace OldPV2 LV [NewPVs]
New devices require synchronization with existing devices.
See Synchronization.
If integrty is in use, it will need to be disabled before repair/replace
commands can be used (lvconvert --raidintegrity n). Integrity can be
enabled again afterward (lvconvert --raidintegrity y).
Refreshing an LV
Refreshing a RAID LV clears any transient device failures (device was
temporarily disconnected) and returns the LV to its fully redundant
mode. Restoring a device will usually require at least partial synchro-
nization (see Synchronization). Failure to clear a transient failure
results in the RAID LV operating in degraded mode until it is reacti-
vated. Use the lvchange command to refresh an LV:
lvchange --refresh LV
# lvs -o name,vgname,segtype,attr,size vg
LV VG Type Attr LSize
lv vg raid1 Rwi-a-r-r- 100.00g
# lvchange --refresh vg/lv
# lvs -o name,vgname,segtype,attr,size vg
LV VG Type Attr LSize
lv vg raid1 Rwi-a-r--- 100.00g
Automatic repair
If a device in a RAID LV fails, device-mapper in the kernel notifies the
dmeventd(8) monitoring process (see Monitoring). dmeventd can be con-
figured to automatically respond using:
lvm.conf(5) activation/raid_fault_policy
Possible settings are:
warn A warning is added to the system log indicating that a device has
failed in the RAID LV. It is left to the user to repair the LV,
e.g. replace failed devices.
allocate
dmeventd automatically attempts to repair the LV using spare de-
vices in the VG. Note that even a transient failure is treated
as a permanent failure under this setting. A new device is allo-
cated and full synchronization is started.
The specific command run by dmeventd(8) to warn or repair is:
lvconvert --repair --use-policies LV
Corrupted Data
Data on a device can be corrupted due to hardware errors without the de-
vice ever being disconnected or there being any fault in the software.
This should be rare, and can be detected (see Scrubbing).
Rebuild specific PVs
If specific PVs in a RAID LV are known to have corrupt data, the data on
those PVs can be reconstructed with:
lvchange --rebuild PV LV
The rebuild option can be repeated with different PVs to replace the
data on multiple PVs.
DATA INTEGRITY
The device mapper integrity target can be used in combination with RAID
levels 1,4,5,6,10 to detect and correct data corruption in RAID images.
A dm-integrity layer is placed above each RAID image, and an extra sub
LV is created to hold integrity metadata (data checksums) for each RAID
image. When data is read from an image, integrity checksums are used to
detect corruption. If detected, dm-raid reads the data from another
(good) image to return to the caller. dm-raid will also automatically
write the good data back to the image with bad data to correct the cor-
ruption.
When creating a RAID LV with integrity, or adding integrity, space is
required for integrity metadata. Every 500MB of LV data requires an ad-
ditional 4MB to be allocated for integrity metadata, for each RAID im-
age.
Create a RAID LV with integrity:
lvcreate --type raidN --raidintegrity y
Add integrity to an existing RAID LV:
lvconvert --raidintegrity y LV
Remove integrity from a RAID LV:
lvconvert --raidintegrity n LV
Integrity options
--raidintegritymode journal|bitmap
Use a journal (default) or bitmap for keeping integrity checksums
consistent in case of a crash. The bitmap areas are recalculated
after a crash, so corruption in those areas would not be de-
tected. A journal does not have this problem. The journal mode
doubles writes to storage, but can improve performance for scat-
tered writes packed into a single journal write. bitmap mode can
in theory achieve full write throughput of the device, but would
not benefit from the potential scattered write optimization.
--raidintegrityblocksize 512|1024|2048|4096
The block size to use for dm-integrity on raid images. The in-
tegrity block size should usually match the device logical block
size, or the file system sector/block sizes. It may be less than
the file system sector/block size, but not less than the device
logical block size. Possible values: 512, 1024, 2048, 4096.
--integritysettings key=val
dm-integrity kernel tunable options can be specified here. Set-
tings can be included with lvcreate or lvconvert when integrity
is first enabled, or changed with lvchange on an existing, inac-
tive LV. See kernel documentation for descriptions of tunable
options. Repeat the option to set multiple values. Use lvs -a
-o integritysettings VG/LV_rimage_N to display configured values.
Use lvchange --integritysettings "" to clear all configured val-
ues (dm-integrity will use its defaults.)
Integrity initialization
When integrity is added to an LV, the kernel needs to initialize the in-
tegrity metadata (crc32 checksums) for all blocks in the LV. The data
corruption checking performed by dm-integrity will only operate on areas
of the LV that are already initialized. The progress of integrity ini-
tialization is reported by the "syncpercent" LV reporting field (and un-
der the Cpy%Sync lvs column.)
Integrity limitations
To work around some limitations, it is possible to remove integrity from
the LV, make the change, then add integrity again. (Integrity metadata
would need to initialized when added again.)
LVM must be able to allocate the integrity metadata sub LV on a single
PV that is already in use by the associated RAID image. This can poten-
tially cause a problem during lvextend if the original PV holding the
image and integrity metadata is full. To work around this limitation,
remove integrity, extend the LV, and add integrity again.
Additional RAID images can be added to raid1 LVs, but not to other raid
levels.
A raid1 LV with integrity cannot be converted to linear (remove in-
tegrity to do this.)
RAID LVs with integrity cannot yet be used as sub LVs with other LV
types.
The following are not yet permitted on RAID LVs with integrity: lvre-
duce, pvmove, lvconvert --splitmirrors, lvchange --rebuild.
RAID1 TUNING
A RAID1 LV can be tuned so that certain devices are avoided for reading
while all devices are still written to.
lvchange --[raid]writemostly PV[:y|n|t] LV
The specified device will be marked as "write mostly", which means that
reading from this device will be avoided, and other devices will be pre-
ferred for reading (unless no other devices are available.) This mini-
mizes the I/O to the specified device.
If the PV name has no suffix, the write mostly attribute is set. If the
PV name has the suffix :n, the write mostly attribute is cleared, and
the suffix :t toggles the current setting.
The write mostly option can be repeated on the command line to change
multiple devices at once.
To report the current write mostly setting, the lvs attr field will show
the letter "w" in the 9th position when write mostly is set:
lvs -a -o name,attr
When a device is marked write mostly, the maximum number of outstanding
writes to that device can be configured. Once the maximum is reached,
further writes become synchronous. When synchronous, a write to the LV
will not complete until writes to all the mirror images are complete.
lvchange --[raid]writebehind Number LV
To report the current write behind setting, run:
lvs -o name,raid_write_behind
When write behind is not configured, or set to 0, all LV writes are syn-
chronous.
RAID TAKEOVER
RAID takeover is converting a RAID LV from one RAID level to another,
e.g. raid5 to raid6. Changing the RAID level is usually done to in-
crease or decrease resilience to device failures or to restripe LVs.
This is done using lvconvert and specifying the new RAID level as the LV
type:
lvconvert --type RaidLevel LV [PVs]
The most common and recommended RAID takeover conversions are:
linear to raid1
Linear is a single image of LV data, and converting it to raid1
adds a mirror image which is a direct copy of the original linear
image.
striped/raid0 to raid4/5/6
Adding parity devices to a striped volume results in raid4/5/6.
Unnatural conversions that are not recommended include converting be-
tween striped and non-striped types. This is because file systems often
optimize I/O patterns based on device striping values. If those values
change, it can decrease performance.
Converting to a higher RAID level requires allocating new SubLVs to hold
RAID metadata, and new SubLVs to hold parity blocks for LV data. Con-
verting to a lower RAID level removes the SubLVs that are no longer
needed.
Conversion often requires full synchronization of the RAID LV (see Syn-
chronization). Converting to RAID1 requires copying all LV data blocks
to N new images on new devices. Converting to a parity RAID level re-
quires reading all LV data blocks, calculating parity, and writing the
new parity blocks. Synchronization can take a long time depending on
the throughput of the devices used and the size of the RaidLV. It can
degrade performance. Rate controls also apply to conversion; see --min-
recoveryrate and --maxrecoveryrate.
Warning: though it is possible to create striped LVs with up to 128
stripes, a maximum of 64 stripes can be converted to raid0, 63 to
raid4/5 and 62 to raid6 because of the added parity SubLVs. A striped
LV with a maximum of 32 stripes can be converted to raid10.
The following takeover conversions are currently possible:
• between striped and raid0.
• between linear and raid1.
• between mirror and raid1.
• between raid1 with two images and raid4/5.
• between striped/raid0 and raid4.
• between striped/raid0 and raid5.
• between striped/raid0 and raid6.
• between raid4 and raid5.
• between raid4/raid5 and raid6.
• between striped/raid0 and raid10.
• between striped and raid4.
Indirect conversions
Converting from one raid level to another may require multiple steps,
converting first to intermediate raid levels.
linear to raid6
To convert an LV from linear to raid6:
1. convert to raid1 with two images
2. convert to raid5 (internally raid5_ls) with two images
3. convert to raid5 with three or more stripes (reshape)
4. convert to raid6 (internally raid6_ls_6)
5. convert to raid6 (internally raid6_zr, reshape)
The commands to perform the steps above are:
1. lvconvert --type raid1 --mirrors 1 LV
2. lvconvert --type raid5 LV
3. lvconvert --stripes 3 LV
4. lvconvert --type raid6 LV
5. lvconvert --type raid6 LV
The final conversion from raid6_ls_6 to raid6_zr is done to avoid the
potential write/recovery performance reduction in raid6_ls_6 because of
the dedicated parity device. raid6_zr rotates data and parity blocks to
avoid this.
linear to striped
To convert an LV from linear to striped:
1. convert to raid1 with two images
2. convert to raid5_n
3. convert to raid5_n with five 128k stripes (reshape)
4. convert raid5_n to striped
The commands to perform the steps above are:
1. lvconvert --type raid1 --mirrors 1 LV
2. lvconvert --type raid5_n LV
3. lvconvert --stripes 5 --stripesize 128k LV
4. lvconvert --type striped LV
The raid5_n type in step 2 is used because it has dedicated parity Sub-
LVs at the end, and can be converted to striped directly. The stripe
size is increased in step 3 to add extra space for the conversion
process. This step grows the LV size by a factor of five. After con-
version, this extra space can be reduced (or used to grow the file sys-
tem using the LV).
Reversing these steps will convert a striped LV to linear.
raid6 to striped
To convert an LV from raid6_nr to striped:
1. convert to raid6_n_6
2. convert to striped
The commands to perform the steps above are:
1. lvconvert --type raid6_n_6 LV
2. lvconvert --type striped LV
Examples
Converting an LV from linear to raid1.
# lvs -a -o name,segtype,size vg
LV Type LSize
lv linear 300.00g
# lvconvert --type raid1 --mirrors 1 vg/lv
# lvs -a -o name,segtype,size vg
LV Type LSize
lv raid1 300.00g
[lv_rimage_0] linear 300.00g
[lv_rimage_1] linear 300.00g
[lv_rmeta_0] linear 3.00m
[lv_rmeta_1] linear 3.00m
Converting an LV from mirror to raid1.
# lvs -a -o name,segtype,size vg
LV Type LSize
lv mirror 100.00g
[lv_mimage_0] linear 100.00g
[lv_mimage_1] linear 100.00g
[lv_mlog] linear 3.00m
# lvconvert --type raid1 vg/lv
# lvs -a -o name,segtype,size vg
LV Type LSize
lv raid1 100.00g
[lv_rimage_0] linear 100.00g
[lv_rimage_1] linear 100.00g
[lv_rmeta_0] linear 3.00m
[lv_rmeta_1] linear 3.00m
Converting an LV from linear to raid1 (with 3 images).
# lvconvert --type raid1 --mirrors 2 vg/lv
Converting an LV from striped (with 4 stripes) to raid6_n_6.
# lvcreate --stripes 4 -L64M -n lv vg
# lvconvert --type raid6 vg/lv
# lvs -a -o lv_name,segtype,sync_percent,data_copies
LV Type Cpy%Sync #Cpy
lv raid6_n_6 100.00 3
[lv_rimage_0] linear
[lv_rimage_1] linear
[lv_rimage_2] linear
[lv_rimage_3] linear
[lv_rimage_4] linear
[lv_rimage_5] linear
[lv_rmeta_0] linear
[lv_rmeta_1] linear
[lv_rmeta_2] linear
[lv_rmeta_3] linear
[lv_rmeta_4] linear
[lv_rmeta_5] linear
This convert begins by allocating MetaLVs (rmeta_#) for each of the ex-
isting stripe devices. It then creates 2 additional MetaLV/DataLV pairs
(rmeta_#/rimage_#) for dedicated raid6 parity.
If rotating data/parity is required, such as with raid6_nr, it must be
done by reshaping (see below).
RAID RESHAPING
RAID reshaping is changing attributes of a RAID LV while keeping the
same RAID level. This includes changing RAID layout, stripe size, or
number of stripes.
When changing the RAID layout or stripe size, no new SubLVs (MetaLVs or
DataLVs) need to be allocated, but DataLVs are extended by a small
amount (typically 1 extent). The extra space allows blocks in a stripe
to be updated safely, and not be corrupted in case of a crash. If a
crash occurs, reshaping can just be restarted.
(If blocks in a stripe were updated in place, a crash could leave them
partially updated and corrupted. Instead, an existing stripe is qui-
esced, read, changed in layout, and the new stripe written to free
space. Once that is done, the new stripe is unquiesced and used.)
Examples
(Command output shown in examples may change.)
Converting raid6_n_6 to raid6_nr with rotating data/parity.
This conversion naturally follows a previous conversion from
striped/raid0 to raid6_n_6 (shown above). It completes the transition
to a more traditional RAID6.
# lvs -o lv_name,segtype,sync_percent,data_copies
LV Type Cpy%Sync #Cpy
lv raid6_n_6 100.00 3
[lv_rimage_0] linear
[lv_rimage_1] linear
[lv_rimage_2] linear
[lv_rimage_3] linear
[lv_rimage_4] linear
[lv_rimage_5] linear
[lv_rmeta_0] linear
[lv_rmeta_1] linear
[lv_rmeta_2] linear
[lv_rmeta_3] linear
[lv_rmeta_4] linear
[lv_rmeta_5] linear
# lvconvert --type raid6_nr vg/lv
# lvs -a -o lv_name,segtype,sync_percent,data_copies
LV Type Cpy%Sync #Cpy
lv raid6_nr 100.00 3
[lv_rimage_0] linear
[lv_rimage_0] linear
[lv_rimage_1] linear
[lv_rimage_1] linear
[lv_rimage_2] linear
[lv_rimage_2] linear
[lv_rimage_3] linear
[lv_rimage_3] linear
[lv_rimage_4] linear
[lv_rimage_5] linear
[lv_rmeta_0] linear
[lv_rmeta_1] linear
[lv_rmeta_2] linear
[lv_rmeta_3] linear
[lv_rmeta_4] linear
[lv_rmeta_5] linear
The DataLVs are larger (additional segment in each) which provides space
for out-of-place reshaping. The result is:
# lvs -a -o lv_name,segtype,seg_pe_ranges,dataoffset
LV Type PE Ranges DOff
lv raid6_nr lv_rimage_0:0-32 \
lv_rimage_1:0-32 \
lv_rimage_2:0-32 \
lv_rimage_3:0-32
[lv_rimage_0] linear /dev/sda:0-31 2048
[lv_rimage_0] linear /dev/sda:33-33
[lv_rimage_1] linear /dev/sdaa:0-31 2048
[lv_rimage_1] linear /dev/sdaa:33-33
[lv_rimage_2] linear /dev/sdab:1-33 2048
[lv_rimage_3] linear /dev/sdac:1-33 2048
[lv_rmeta_0] linear /dev/sda:32-32
[lv_rmeta_1] linear /dev/sdaa:32-32
[lv_rmeta_2] linear /dev/sdab:0-0
[lv_rmeta_3] linear /dev/sdac:0-0
All segments with PE ranges '33-33' provide the out-of-place reshape
space. The dataoffset column shows that the data was moved from initial
offset 0 to 2048 sectors on each component DataLV.
For performance reasons the raid6_nr RaidLV can be restriped. Convert
it from 3-way striped to 5-way-striped.
# lvconvert --stripes 5 vg/lv
Using default stripesize 64.00 KiB.
WARNING: Adding stripes to active logical volume vg/lv will \
grow it from 99 to 165 extents!
Run "lvresize -l99 vg/lv" to shrink it or use the additional \
capacity.
Logical volume vg/lv successfully converted.
# lvs vg/lv
LV VG Attr LSize Cpy%Sync
lv vg rwi-a-r-s- 652.00m 52.94
# lvs -a -o lv_name,attr,segtype,seg_pe_ranges,dataoffset vg
LV Attr Type PE Ranges DOff
lv rwi-a-r--- raid6_nr lv_rimage_0:0-33 \
lv_rimage_1:0-33 \
lv_rimage_2:0-33 ... \
lv_rimage_5:0-33 \
lv_rimage_6:0-33 0
[lv_rimage_0] iwi-aor--- linear /dev/sda:0-32 0
[lv_rimage_0] iwi-aor--- linear /dev/sda:34-34
[lv_rimage_1] iwi-aor--- linear /dev/sdaa:0-32 0
[lv_rimage_1] iwi-aor--- linear /dev/sdaa:34-34
[lv_rimage_2] iwi-aor--- linear /dev/sdab:0-32 0
[lv_rimage_2] iwi-aor--- linear /dev/sdab:34-34
[lv_rimage_3] iwi-aor--- linear /dev/sdac:1-34 0
[lv_rimage_4] iwi-aor--- linear /dev/sdad:1-34 0
[lv_rimage_5] iwi-aor--- linear /dev/sdae:1-34 0
[lv_rimage_6] iwi-aor--- linear /dev/sdaf:1-34 0
[lv_rmeta_0] ewi-aor--- linear /dev/sda:33-33
[lv_rmeta_1] ewi-aor--- linear /dev/sdaa:33-33
[lv_rmeta_2] ewi-aor--- linear /dev/sdab:33-33
[lv_rmeta_3] ewi-aor--- linear /dev/sdac:0-0
[lv_rmeta_4] ewi-aor--- linear /dev/sdad:0-0
[lv_rmeta_5] ewi-aor--- linear /dev/sdae:0-0
[lv_rmeta_6] ewi-aor--- linear /dev/sdaf:0-0
Stripes also can be removed from raid5 and 6. Convert the 5-way striped
raid6_nr LV to 4-way-striped. The force option needs to be used, be-
cause removing stripes (i.e. image SubLVs) from a RaidLV will shrink its
size.
# lvconvert --stripes 4 vg/lv
Using default stripesize 64.00 KiB.
WARNING: Removing stripes from active logical volume vg/lv will \
shrink it from 660.00 MiB to 528.00 MiB!
THIS MAY DESTROY (PARTS OF) YOUR DATA!
If that leaves the logical volume larger than 206 extents due \
to stripe rounding,
you may want to grow the content afterwards (filesystem etc.)
WARNING: to remove freed stripes after the conversion has finished,\
you have to run "lvconvert --stripes 4 vg/lv"
Logical volume vg/lv successfully converted.
# lvs -a -o lv_name,attr,segtype,seg_pe_ranges,dataoffset vg
LV Attr Type PE Ranges DOff
lv rwi-a-r-s- raid6_nr lv_rimage_0:0-33 \
lv_rimage_1:0-33 \
lv_rimage_2:0-33 ... \
lv_rimage_5:0-33 \
lv_rimage_6:0-33 0
[lv_rimage_0] Iwi-aor--- linear /dev/sda:0-32 0
[lv_rimage_0] Iwi-aor--- linear /dev/sda:34-34
[lv_rimage_1] Iwi-aor--- linear /dev/sdaa:0-32 0
[lv_rimage_1] Iwi-aor--- linear /dev/sdaa:34-34
[lv_rimage_2] Iwi-aor--- linear /dev/sdab:0-32 0
[lv_rimage_2] Iwi-aor--- linear /dev/sdab:34-34
[lv_rimage_3] Iwi-aor--- linear /dev/sdac:1-34 0
[lv_rimage_4] Iwi-aor--- linear /dev/sdad:1-34 0
[lv_rimage_5] Iwi-aor--- linear /dev/sdae:1-34 0
[lv_rimage_6] Iwi-aor-R- linear /dev/sdaf:1-34 0
[lv_rmeta_0] ewi-aor--- linear /dev/sda:33-33
[lv_rmeta_1] ewi-aor--- linear /dev/sdaa:33-33
[lv_rmeta_2] ewi-aor--- linear /dev/sdab:33-33
[lv_rmeta_3] ewi-aor--- linear /dev/sdac:0-0
[lv_rmeta_4] ewi-aor--- linear /dev/sdad:0-0
[lv_rmeta_5] ewi-aor--- linear /dev/sdae:0-0
[lv_rmeta_6] ewi-aor-R- linear /dev/sdaf:0-0
The 's' in column 9 of the attribute field shows the RaidLV is still re-
shaping. The 'R' in the same column of the attribute field shows the
freed image Sub LVs which will need removing once the reshaping fin-
ished.
# lvs -o lv_name,attr,segtype,seg_pe_ranges,dataoffset vg
LV Attr Type PE Ranges DOff
lv rwi-a-r-R- raid6_nr lv_rimage_0:0-33 \
lv_rimage_1:0-33 \
lv_rimage_2:0-33 ... \
lv_rimage_5:0-33 \
lv_rimage_6:0-33 8192
Now that the reshape is finished the 'R' attribute on the RaidLV shows
images can be removed.
# lvs -o lv_name,attr,segtype,seg_pe_ranges,dataoffset vg
LV Attr Type PE Ranges DOff
lv rwi-a-r-R- raid6_nr lv_rimage_0:0-33 \
lv_rimage_1:0-33 \
lv_rimage_2:0-33 ... \
lv_rimage_5:0-33 \
lv_rimage_6:0-33 8192
This is achieved by repeating the command ("lvconvert --stripes 4 vg/lv"
would be sufficient).
# lvconvert --stripes 4 vg/lv
Using default stripesize 64.00 KiB.
Logical volume vg/lv successfully converted.
# lvs -a -o lv_name,attr,segtype,seg_pe_ranges,dataoffset vg
LV Attr Type PE Ranges DOff
lv rwi-a-r--- raid6_nr lv_rimage_0:0-33 \
lv_rimage_1:0-33 \
lv_rimage_2:0-33 ... \
lv_rimage_5:0-33 8192
[lv_rimage_0] iwi-aor--- linear /dev/sda:0-32 8192
[lv_rimage_0] iwi-aor--- linear /dev/sda:34-34
[lv_rimage_1] iwi-aor--- linear /dev/sdaa:0-32 8192
[lv_rimage_1] iwi-aor--- linear /dev/sdaa:34-34
[lv_rimage_2] iwi-aor--- linear /dev/sdab:0-32 8192
[lv_rimage_2] iwi-aor--- linear /dev/sdab:34-34
[lv_rimage_3] iwi-aor--- linear /dev/sdac:1-34 8192
[lv_rimage_4] iwi-aor--- linear /dev/sdad:1-34 8192
[lv_rimage_5] iwi-aor--- linear /dev/sdae:1-34 8192
[lv_rmeta_0] ewi-aor--- linear /dev/sda:33-33
[lv_rmeta_1] ewi-aor--- linear /dev/sdaa:33-33
[lv_rmeta_2] ewi-aor--- linear /dev/sdab:33-33
[lv_rmeta_3] ewi-aor--- linear /dev/sdac:0-0
[lv_rmeta_4] ewi-aor--- linear /dev/sdad:0-0
[lv_rmeta_5] ewi-aor--- linear /dev/sdae:0-0
# lvs -a -o lv_name,attr,segtype,reshapelen vg
LV Attr Type RSize
lv rwi-a-r--- raid6_nr 24.00m
[lv_rimage_0] iwi-aor--- linear 4.00m
[lv_rimage_0] iwi-aor--- linear
[lv_rimage_1] iwi-aor--- linear 4.00m
[lv_rimage_1] iwi-aor--- linear
[lv_rimage_2] iwi-aor--- linear 4.00m
[lv_rimage_2] iwi-aor--- linear
[lv_rimage_3] iwi-aor--- linear 4.00m
[lv_rimage_4] iwi-aor--- linear 4.00m
[lv_rimage_5] iwi-aor--- linear 4.00m
[lv_rmeta_0] ewi-aor--- linear
[lv_rmeta_1] ewi-aor--- linear
[lv_rmeta_2] ewi-aor--- linear
[lv_rmeta_3] ewi-aor--- linear
[lv_rmeta_4] ewi-aor--- linear
[lv_rmeta_5] ewi-aor--- linear
Future developments might include automatic removal of the freed images.
If the reshape space shall be removed any lvconvert command not changing
the layout can be used:
# lvconvert --stripes 4 vg/lv
Using default stripesize 64.00 KiB.
No change in RAID LV vg/lv layout, freeing reshape space.
Logical volume vg/lv successfully converted.
# lvs -a -o lv_name,attr,segtype,reshapelen vg
LV Attr Type RSize
lv rwi-a-r--- raid6_nr 0
[lv_rimage_0] iwi-aor--- linear 0
[lv_rimage_0] iwi-aor--- linear
[lv_rimage_1] iwi-aor--- linear 0
[lv_rimage_1] iwi-aor--- linear
[lv_rimage_2] iwi-aor--- linear 0
[lv_rimage_2] iwi-aor--- linear
[lv_rimage_3] iwi-aor--- linear 0
[lv_rimage_4] iwi-aor--- linear 0
[lv_rimage_5] iwi-aor--- linear 0
[lv_rmeta_0] ewi-aor--- linear
[lv_rmeta_1] ewi-aor--- linear
[lv_rmeta_2] ewi-aor--- linear
[lv_rmeta_3] ewi-aor--- linear
[lv_rmeta_4] ewi-aor--- linear
[lv_rmeta_5] ewi-aor--- linear
In case the RaidLV should be converted to striped:
# lvconvert --type striped vg/lv
Unable to convert LV vg/lv from raid6_nr to striped.
Converting vg/lv from raid6_nr is directly possible to the \
following layouts:
raid6_nc
raid6_zr
raid6_la_6
raid6_ls_6
raid6_ra_6
raid6_rs_6
raid6_n_6
A direct conversion isn't possible thus the command informed about the
possible ones. raid6_n_6 is suitable to convert to striped so convert
to it first (this is a reshape changing the raid6 layout from raid6_nr
to raid6_n_6).
# lvconvert --type raid6_n_6
Using default stripesize 64.00 KiB.
Converting raid6_nr LV vg/lv to raid6_n_6.
Are you sure you want to convert raid6_nr LV vg/lv? [y/n]: y
Logical volume vg/lv successfully converted.
Wait for the reshape to finish.
# lvconvert --type striped vg/lv
Logical volume vg/lv successfully converted.
# lvs -o lv_name,attr,segtype,seg_pe_ranges,dataoffset vg
LV Attr Type PE Ranges DOff
lv -wi-a----- striped /dev/sda:2-32 \
/dev/sdaa:2-32 \
/dev/sdab:2-32 \
/dev/sdac:3-33
lv -wi-a----- striped /dev/sda:34-35 \
/dev/sdaa:34-35 \
/dev/sdab:34-35 \
/dev/sdac:34-35
From striped we can convert to raid10
# lvconvert --type raid10 vg/lv
Using default stripesize 64.00 KiB.
Logical volume vg/lv successfully converted.
# lvs -o lv_name,attr,segtype,seg_pe_ranges,dataoffset vg
LV Attr Type PE Ranges DOff
lv rwi-a-r--- raid10 lv_rimage_0:0-32 \
lv_rimage_4:0-32 \
lv_rimage_1:0-32 ... \
lv_rimage_3:0-32 \
lv_rimage_7:0-32 0
# lvs -a -o lv_name,attr,segtype,seg_pe_ranges,dataoffset vg
WARNING: Cannot find matching striped segment for vg/lv_rimage_3.
LV Attr Type PE Ranges DOff
lv rwi-a-r--- raid10 lv_rimage_0:0-32 \
lv_rimage_4:0-32 \
lv_rimage_1:0-32 ... \
lv_rimage_3:0-32 \
lv_rimage_7:0-32 0
[lv_rimage_0] iwi-aor--- linear /dev/sda:2-32 0
[lv_rimage_0] iwi-aor--- linear /dev/sda:34-35
[lv_rimage_1] iwi-aor--- linear /dev/sdaa:2-32 0
[lv_rimage_1] iwi-aor--- linear /dev/sdaa:34-35
[lv_rimage_2] iwi-aor--- linear /dev/sdab:2-32 0
[lv_rimage_2] iwi-aor--- linear /dev/sdab:34-35
[lv_rimage_3] iwi-XXr--- linear /dev/sdac:3-35 0
[lv_rimage_4] iwi-aor--- linear /dev/sdad:1-33 0
[lv_rimage_5] iwi-aor--- linear /dev/sdae:1-33 0
[lv_rimage_6] iwi-aor--- linear /dev/sdaf:1-33 0
[lv_rimage_7] iwi-aor--- linear /dev/sdag:1-33 0
[lv_rmeta_0] ewi-aor--- linear /dev/sda:0-0
[lv_rmeta_1] ewi-aor--- linear /dev/sdaa:0-0
[lv_rmeta_2] ewi-aor--- linear /dev/sdab:0-0
[lv_rmeta_3] ewi-aor--- linear /dev/sdac:0-0
[lv_rmeta_4] ewi-aor--- linear /dev/sdad:0-0
[lv_rmeta_5] ewi-aor--- linear /dev/sdae:0-0
[lv_rmeta_6] ewi-aor--- linear /dev/sdaf:0-0
[lv_rmeta_7] ewi-aor--- linear /dev/sdag:0-0
raid10 allows to add stripes but can't remove them.
A more elaborate example to convert from linear to striped with interim
conversions to raid1 then raid5 followed by restripe (4 steps).
We start with the linear LV.
# lvs -a -o name,size,segtype,syncpercent,datastripes,\
stripesize,reshapelenle,devices vg
LV LSize Type Cpy%Sync #DStr Stripe RSize Devices
lv 128.00m linear 1 0 /dev/sda(0)
Then convert it to a 2-way raid1.
# lvconvert --mirrors 1 vg/lv
Logical volume vg/lv successfully converted.
# lvs -a -o name,size,segtype,datastripes,\
stripesize,reshapelenle,devices vg
LV LSize Type #DStr Stripe RSize Devices
lv 128.00m raid1 2 0 lv_rimage_0(0),\
lv_rimage_1(0)
[lv_rimage_0] 128.00m linear 1 0 /dev/sda(0)
[lv_rimage_1] 128.00m linear 1 0 /dev/sdhx(1)
[lv_rmeta_0] 4.00m linear 1 0 /dev/sda(32)
[lv_rmeta_1] 4.00m linear 1 0 /dev/sdhx(0)
Once the raid1 LV is fully synchronized we convert it to raid5_n (only
2-way raid1 LVs can be converted to raid5). We select raid5_n here be-
cause it has dedicated parity SubLVs at the end and can be converted to
striped directly without any additional conversion.
# lvconvert --type raid5_n vg/lv
Using default stripesize 64.00 KiB.
Logical volume vg/lv successfully converted.
# lvs -a -o name,size,segtype,syncpercent,datastripes,\
stripesize,reshapelenle,devices vg
LV LSize Type #DStr Stripe RSize Devices
lv 128.00m raid5_n 1 64.00k 0 lv_rimage_0(0),\
lv_rimage_1(0)
[lv_rimage_0] 128.00m linear 1 0 0 /dev/sda(0)
[lv_rimage_1] 128.00m linear 1 0 0 /dev/sdhx(1)
[lv_rmeta_0] 4.00m linear 1 0 /dev/sda(32)
[lv_rmeta_1] 4.00m linear 1 0 /dev/sdhx(0)
Now we'll change the number of data stripes from 1 to 5 and request 128K
stripe size in one command. This will grow the size of the LV by a fac-
tor of 5 (we add 4 data stripes to the one given). That additional
space can be used by e.g. growing any contained filesystem or the LV can
be reduced in size after the reshaping conversion has finished.
# lvconvert --stripesize 128k --stripes 5 vg/lv
Converting stripesize 64.00 KiB of raid5_n LV vg/lv to 128.00 KiB.
WARNING: Adding stripes to active logical volume vg/lv will grow \
it from 32 to 160 extents!
Run "lvresize -l32 vg/lv" to shrink it or use the additional capacity.
Logical volume vg/lv successfully converted.
# lvs -a -o name,size,segtype,datastripes,\
stripesize,reshapelenle,devices
LV LSize Type #DStr Stripe RSize Devices
lv 640.00m raid5_n 5 128.00k 6 lv_rimage_0(0),\
lv_rimage_1(0),\
lv_rimage_2(0),\
lv_rimage_3(0),\
lv_rimage_4(0),\
lv_rimage_5(0)
[lv_rimage_0] 132.00m linear 1 0 1 /dev/sda(33)
[lv_rimage_0] 132.00m linear 1 0 /dev/sda(0)
[lv_rimage_1] 132.00m linear 1 0 1 /dev/sdhx(33)
[lv_rimage_1] 132.00m linear 1 0 /dev/sdhx(1)
[lv_rimage_2] 132.00m linear 1 0 1 /dev/sdhw(33)
[lv_rimage_2] 132.00m linear 1 0 /dev/sdhw(1)
[lv_rimage_3] 132.00m linear 1 0 1 /dev/sdhv(33)
[lv_rimage_3] 132.00m linear 1 0 /dev/sdhv(1)
[lv_rimage_4] 132.00m linear 1 0 1 /dev/sdhu(33)
[lv_rimage_4] 132.00m linear 1 0 /dev/sdhu(1)
[lv_rimage_5] 132.00m linear 1 0 1 /dev/sdht(33)
[lv_rimage_5] 132.00m linear 1 0 /dev/sdht(1)
[lv_rmeta_0] 4.00m linear 1 0 /dev/sda(32)
[lv_rmeta_1] 4.00m linear 1 0 /dev/sdhx(0)
[lv_rmeta_2] 4.00m linear 1 0 /dev/sdhw(0)
[lv_rmeta_3] 4.00m linear 1 0 /dev/sdhv(0)
[lv_rmeta_4] 4.00m linear 1 0 /dev/sdhu(0)
[lv_rmeta_5] 4.00m linear 1 0 /dev/sdht(0)
Once the conversion has finished we can convert to striped.
# lvconvert --type striped vg/lv
Logical volume vg/lv successfully converted.
# lvs -a -o name,size,segtype,datastripes,\
stripesize,reshapelenle,devices vg
LV LSize Type #DStr Stripe RSize Devices
lv 640.00m striped 5 128.00k /dev/sda(33),\
/dev/sdhx(33),\
/dev/sdhw(33),\
/dev/sdhv(33),\
/dev/sdhu(33)
lv 640.00m striped 5 128.00k /dev/sda(0),\
/dev/sdhx(1),\
/dev/sdhw(1),\
/dev/sdhv(1),\
/dev/sdhu(1)
Reversing these steps will convert a given striped LV to linear.
Mind the facts that stripes are removed thus the capacity of the RaidLV
will shrink and that changing the RaidLV layout will influence its per-
formance.
"lvconvert --stripes 1 vg/lv" for converting to 1 stripe will inform up-
front about the reduced size to allow for resizing the content or grow-
ing the RaidLV before actually converting to 1 stripe. The --force op-
tion is needed to allow stripe removing conversions to prevent data
loss.
Of course any interim step can be the intended last one (e.g. striped →
raid1).
RAID5 VARIANTS
raid5_ls
• RAID5 left symmetric
• Rotating parity N with data restart
raid5_la
• RAID5 left asymmetric
• Rotating parity N with data continuation
raid5_rs
• RAID5 right symmetric
• Rotating parity 0 with data restart
raid5_ra
• RAID5 right asymmetric
• Rotating parity 0 with data continuation
raid5_n
• RAID5 parity n
• Dedicated parity device n used for striped/raid0 conversions
• Used for RAID Takeover
RAID6 VARIANTS
raid6
• RAID6 zero restart (aka left symmetric)
• Rotating parity 0 with data restart
• Same as raid6_zr
raid6_zr
• RAID6 zero restart (aka left symmetric)
• Rotating parity 0 with data restart
raid6_nr
• RAID6 N restart (aka right symmetric)
• Rotating parity N with data restart
raid6_nc
• RAID6 N continue
• Rotating parity N with data continuation
raid6_n_6
• RAID6 last parity devices
• Fixed dedicated last devices (P-Syndrome N-1 and Q-Syndrome N)
with striped data used for striped/raid0 conversions
• Used for RAID Takeover
raid6_{ls,rs,la,ra}_6
• RAID6 last parity device
• Dedicated last parity device used for conversions from/to
raid5_{ls,rs,la,ra}
raid6_ls_6
• RAID6 N continue
• Same as raid5_ls for N-1 devices with fixed Q-Syndrome N
• Used for RAID Takeover
raid6_la_6
• RAID6 N continue
• Same as raid5_la for N-1 devices with fixed Q-Syndrome N
• Used forRAID Takeover
raid6_rs_6
• RAID6 N continue
• Same as raid5_rs for N-1 devices with fixed Q-Syndrome N
• Used for RAID Takeover
raid6_ra_6
• RAID6 N continue
• Same as raid5_ra for N-1 devices with fixed Q-Syndrome N
• Used for RAID Takeover
HISTORY
The 2.6.38-rc1 version of the Linux kernel introduced a device-mapper
target to interface with the software RAID (MD) personalities. This
provided device-mapper with RAID 4/5/6 capabilities and a larger devel-
opment community. Later, support for RAID1, RAID10, and RAID1E (RAID 10
variants) were added. Support for these new kernel RAID targets was
added to LVM version 2.02.87. The capabilities of the LVM raid1 type
have surpassed the old mirror type. raid1 is now recommended instead of
mirror. raid1 became the default for mirroring in LVM version 2.02.100.
SEE ALSO
lvm(8), lvm.conf(5), lvcreate(8), lvconvert(8), lvchange(8),
lvextend(8), dmeventd(8)
Red Hat, Inc LVM TOOLS 2.03.31(2) (2025-02-27) LVMRAID(7)
Generated by dwww version 1.16 on Tue Dec 16 04:58:04 CET 2025.