INTEGRITYSETUP(8) Maintenance Commands INTEGRITYSETUP(8)
NAME
integritysetup - manage dm-integrity (block level integrity) volumes
SYNOPSIS
integritysetup <action> [<options>] <action args>
DESCRIPTION
Integritysetup is used to configure dm-integrity managed device-mapper
mappings.
Device-mapper integrity target provides read-write transparent integrity
checking of block devices. The dm-integrity target emulates an
additional data integrity field per-sector. You can use this additional
field directly with integritysetup utility, or indirectly (for
authenticated encryption) through cryptsetup.
BASIC ACTIONS
Integritysetup supports these operations:
FORMAT
format <device>
Formats <device> (calculates space and dm-integrity superblock and wipes
the device).
<options> can be [--data-device, --batch-mode, --no-wipe,
--journal-size, --interleave-sectors, --tag-size, --integrity,
--integrity-key-size, --integrity-key-file, --sector-size,
--progress-frequency, --progress-json].
OPEN
open <device> <name>
create <name> <device> (OBSOLETE syntax)
Open a mapping with <name> backed by device <device>.
If the integrity algorithm of the device is non-default, then the
algorithm should be specified with the --integrity option. This will not
be detected from the device.
<options> can be [--data-device, --batch-mode, --journal-watermark,
--journal-commit-time, --buffer-sectors, --integrity,
--integrity-key-size, --integrity-key-file, --integrity-no-journal,
--integrity-recalculate,
--integrity-recalculate-reset,--integrity-recovery-mode,
--allow-discards].
CLOSE
close <name>
remove <name> (OBSOLETE syntax)
Removes existing mapping <name>.
<options> can be [--deferred] or [--cancel-deferred]
STATUS
status <name>
Reports status for the active integrity mapping <name>.
DUMP
dump <device>
Reports parameters from on-disk stored superblock.
RESIZE
resize <name>
Resizes an active mapping <name>.
If --size (in 512-bytes sectors) or --device-size are not specified, the
size is computed from the underlying device. After resize, the
recalculating flag is set. If --wipe flag is set and the size of the
device is increased, the newly added section will be wiped.
Increasing the size of integrity volumes is available since the Linux
kernel version 5.7, shrinking should work on older kernels too.
<options> can be [--size, --device-size, --wipe].
OPTIONS
--allow-discards
Allow the use of discard (TRIM) requests for the device. This option
is available since the Linux kernel version 5.7.
--batch-mode, -q
Do not ask for confirmation.
--bitmap-flush-time MS
Bitmap flush time in milliseconds.
WARNING: In case of a crash, it is possible that the data and
integrity tag doesn’t match if the journal is disabled.
--bitmap-sectors-per-bit SECTORS
Number of 512-byte sectors per bitmap bit, the value must be power
of two.
--buffer-sectors SECTORS
The number of sectors in one buffer.
The tag area is accessed using buffers, the large buffer size means
that the I/O size will be larger, but there could be less I/Os
issued.
--cancel-deferred
Removes a previously configured deferred device removal in close
command.
--data-device <data_device>
Specify a separate data device that contains existing data. The
<device> then will contain calculated integrity tags and journal for
data on <data_device>.
NOTE: To not wipe the data device after initial format, also specify
--no-wipe option and activate with --integrity-recalculate to
automatically recalculate integrity tags.
--debug
Run in debug mode with full diagnostic logs. Debug output lines are
always prefixed by #.
--deferred
Defers device removal in close command until the last user closes
it.
--help, -?
Show help text and default parameters.
--integrity, -I ALGORITHM
Use internal integrity calculation (standalone mode). The integrity
algorithm can be CRC (crc32c/crc32), non-cryptographic hash function
(xxhash64) or hash function (sha1, sha256).
For HMAC (hmac-sha256) you have also to specify an integrity key and
its size.
--integrity-bitmap-mode. -B
Use alternate bitmap mode (available since Linux kernel 5.2) where
dm-integrity uses bitmap instead of a journal. If a bit in the
bitmap is 1, the corresponding region’s data and integrity tags are
not synchronized - if the machine crashes, the unsynchronized
regions will be recalculated. The bitmap mode is faster than the
journal mode, because we don’t have to write the data twice, but it
is also less reliable, because if data corruption happens when the
machine crashes, it may not be detected.
--integrity-key-file FILE
The file with the integrity key.
--integrity-key-size BYTES
The size of the data integrity key. Maximum is 4096 bytes.
--integrity-no-journal, -D
Disable journal for integrity device.
--integrity-recalculate
Automatically recalculate integrity tags in kernel on activation.
The device can be used during automatic integrity recalculation but
becomes fully integrity protected only after the background
operation is finished. This option is available since the Linux
kernel version 4.19.
--integrity-recalculate-reset
Restart recalculation from the beginning of the device. It can be
used to change the integrity checksum function. Note it does not
change the tag length. This option is available since the Linux
kernel version 5.13.
--integrity-recovery-mode. -R
Recovery mode (no journal, no tag checking).
--interleave-sectors SECTORS
The number of interleaved sectors.
--journal-commit-time MS
Commit time in milliseconds. When this time passes (and no explicit
flush operation was issued), the journal is written.
--journal-crypt ALGORITHM
Encryption algorithm for journal data area. You can use a block
cipher here such as cbc-aes or a stream cipher, for example,
chacha20 or ctr-aes.
NOTE: The journal encryption options are only intended for testing.
Using journal encryption does not make sense without encryption of
the data.
--journal-crypt-key-file FILE
The file with the journal encryption key.
--journal-crypt-key-size BYTES
The size of the journal encryption key. Maximum is 4096 bytes.
--journal-integrity ALGORITHM
Integrity algorithm for journal area. See --integrity option for
detailed specification.
--journal-integrity-key-file FILE
The file with the integrity key.
--journal-integrity-key-size BYTES
The size of the journal integrity key. Maximum is 4096 bytes.
--journal-size, -j BYTES
Size of the journal.
--journal-watermark PERCENT
Journal watermark in percents. When the size of the journal exceeds
this watermark, the journal flush will be started.
--no-wipe
Do not wipe the device after format. A device that is not initially
wiped will contain invalid checksums.
--progress-frequency <seconds>
Print separate line every <seconds> with wipe progress.
--progress-json
Prints wipe progress data in json format suitable mostly for machine
processing. It prints separate line every half second (or based on
--progress-frequency value). The JSON output looks as follows during
wipe progress (except it’s compact single line):
{
"device":"/dev/sda", // backing device or file
"device_bytes":"8192", // bytes wiped so far
"device_size":"44040192", // total bytes to wipe
"speed":"126877696", // calculated speed in bytes per second (based on progress so far)
"eta_ms":"2520012", // estimated time to finish wipe in milliseconds
"time_ms":"5561235" // total time spent wiping device in milliseconds
}
Note on numbers in JSON output: Due to JSON parsers limitations all
numbers are represented in a string format due to need of full 64bit
unsigned integers.
--sector-size, -s BYTES
Sector size (power of two: 512, 1024, 2048, 4096).
--tag-size, -t BYTES
Size of the integrity tag per-sector (here the integrity function
will store authentication tag).
NOTE: The size can be smaller that output size of the hash function,
in that case only part of the hash will be stored.
--usage
Show short option help.
--verbose, -v
Print more information on command execution.
--version, -V
Show the program version.
--wipe
Wipe the newly allocated area after resize to bigger size. If this
flag is not set, checksums will be calculated for the data
previously stored in the newly allocated area.
LEGACY COMPATIBILITY OPTIONS
WARNING:
Do not use these options until you need compatibility with specific
old kernel.
--integrity-legacy-padding
Use inefficient legacy padding.
--integrity-legacy-hmac
Use old flawed HMAC calculation (also does not protect superblock).
--integrity-legacy-recalculate
Allow insecure recalculating of volumes with HMAC keys
(recalculation offset in superblock is not protected).
RETURN CODES
Integritysetup returns 0 on success and a non-zero value on error.
Error codes are: 1 wrong parameters, 2 no permission, 3 out of memory, 4
wrong device specified, 5 device already exists or device is busy.
NOTES
The dm-integrity target is available since Linux kernel version 4.12.
Format and activation of an integrity device always require superuser
privilege because the superblock is calculated and handled in
dm-integrity kernel target.
EXAMPLES
Format the device with default standalone mode (CRC32C):
integritysetup format <device>
Open the device with default parameters:
integritysetup open <device> test
Format the device in standalone mode for use with HMAC(SHA256):
integritysetup format <device> --tag-size 32 --integrity hmac-sha256
--integrity-key-file <keyfile> --integrity-key-size <key_bytes>
Open (activate) the device with HMAC(SHA256) and HMAC key in file:
integritysetup open <device> test --integrity hmac-sha256
--integrity-key-file <keyfile> --integrity-key-size <key_bytes>
Dump dm-integrity superblock information:
integritysetup dump <device>
DM-INTEGRITY ON-DISK FORMAT
The on-disk format specification available at DMIntegrity
<https://gitlab.com/cryptsetup/cryptsetup/wikis/DMIntegrity> page.
AUTHORS
The integritysetup tool is written by Milan Broz <gmazyland@gmail.com>.
REPORTING BUGS
Report bugs at cryptsetup mailing list <cryptsetup@lists.linux.dev> or
in Issues project section
<https://gitlab.com/cryptsetup/cryptsetup/-/issues/new>.
Please attach output of the failed command with --debug option added.
SEE ALSO
Cryptsetup FAQ
<https://gitlab.com/cryptsetup/cryptsetup/wikis/FrequentlyAskedQuestions>
cryptsetup(8), integritysetup(8) and veritysetup(8)
CRYPTSETUP
Part of cryptsetup project <https://gitlab.com/cryptsetup/cryptsetup/>.
integritysetup 2.7.5 2025-05-04 INTEGRITYSETUP(8)
Generated by dwww version 1.16 on Tue Dec 16 05:09:49 CET 2025.