XXD(1) General Commands Manual XXD(1)
NAME
xxd - make a hex dump or do the reverse.
SYNOPSIS
xxd -h[elp]
xxd [options] [infile [outfile]]
xxd -r[evert] [options] [infile [outfile]]
DESCRIPTION
xxd creates a hex dump of a given file or standard input. It can also
convert a hex dump back to its original binary form. Like uuencode(1)
and uudecode(1) it allows the transmission of binary data in a `mail-
safe' ASCII representation, but has the advantage of decoding to stan-
dard output. Moreover, it can be used to perform binary file patching.
OPTIONS
If no infile is given, standard input is read. If infile is specified
as a `-' character, then input is taken from standard input. If no out-
file is given (or a `-' character is in its place), results are sent to
standard output.
Note that a "lazy" parser is used which does not check for more than the
first option letter, unless the option is followed by a parameter.
Spaces between a single option letter and its parameter are optional.
Parameters to options can be specified in decimal, hexadecimal or octal
notation. Thus -c8, -c 8, -c 010 and -cols 8 are all equivalent.
-a | -autoskip
Toggle autoskip: A single '*' replaces NUL-lines. Default off.
-b | -bits
Switch to bits (binary digits) dump, rather than hex dump. This
option writes octets as eight digits "1"s and "0"s instead of a
normal hexadecimal dump. Each line is preceded by a line number
in hexadecimal and followed by an ASCII (or EBCDIC) representa-
tion. The command line switch -p does not work with this mode.
Can be combined with -i.
-c cols | -cols cols
Format <cols> octets per line. Default 16 (-i: 12, -ps: 30, -b:
6). Max 256. No maximum for -ps. With -ps, 0 results in one long
line of output.
-C | -capitalize
Capitalize variable names in C include file style, when using -i.
-d show offset in decimal instead of hex.
-E | -EBCDIC
Change the character encoding in the righthand column from ASCII
to EBCDIC. This does not change the hexadecimal representation.
The option is meaningless in combinations with -r, -p or -i.
-e Switch to little-endian hex dump. This option treats byte groups
as words in little-endian byte order. The default grouping of 4
bytes may be changed using -g. This option only applies to the
hex dump, leaving the ASCII (or EBCDIC) representation unchanged.
The command line switches -r, -p, -i do not work with this mode.
-g bytes | -groupsize bytes
Separate the output of every <bytes> bytes (two hex characters or
eight bit digits each) by a whitespace. Specify -g 0 to suppress
grouping. <Bytes> defaults to 2 in normal mode, 4 in little-en-
dian mode and 1 in bits mode. Grouping does not apply to Post-
Script or include style.
-h | -help
Print a summary of available commands and exit. No hex dumping
is performed.
-i | -include
Output in C include file style. A complete static array defini-
tion is written (named after the input file), unless xxd reads
from stdin. Can be combined with -b.
-l len | -len len
Stop after writing <len> octets.
-n name | -name name
Override the variable name output when -i is used. The array is
named name and the length is named name_len.
-o offset
Add <offset> to the displayed file position.
-p | -ps | -postscript | -plain
Output in PostScript continuous hex dump style. Also known as
plain hex dump style.
-r | -revert
Reverse operation: convert (or patch) hex dump into binary. If
not writing to stdout, xxd writes into its output file without
truncating it. Use the combination -r -p to read plain hexadeci-
mal dumps without line number information and without a particu-
lar column layout. Additional whitespace and line breaks are al-
lowed anywhere. Use the combination -r -b to read a bits dump in-
stead of a hex dump.
-R when
In the output the hex-value and the value are both colored with
the same color depending on the hex-value. Mostly helping to dif-
ferentiate printable and non-printable characters. when is
never, always, or auto (default: auto). When the $NO_COLOR envi-
ronment variable is set, colorization will be disabled.
-seek offset
When used after -r: revert with <offset> added to file positions
found in hex dump.
-s [+][-]seek
Start at <seek> bytes abs. (or rel.) infile offset. + indicates
that the seek is relative to the current stdin file position
(meaningless when not reading from stdin). - indicates that the
seek should be that many characters from the end of the input (or
if combined with +: before the current stdin file position).
Without -s option, xxd starts at the current file position.
-u Use upper-case hex letters. Default is lower-case.
-v | -version
Show version string.
CAVEATS
xxd -r has some built-in magic while evaluating line number information.
If the output file is seekable, then the line numbers at the start of
each hex dump line may be out of order, lines may be missing, or over-
lapping. In these cases xxd will lseek(2) to the next position. If the
output file is not seekable, only gaps are allowed, which will be filled
by null-bytes.
xxd -r never generates parse errors. Garbage is silently skipped.
When editing hex dumps, please note that xxd -r skips everything on the
input line after reading enough columns of hexadecimal data (see option
-c). This also means that changes to the printable ASCII (or EBCDIC)
columns are always ignored. Reverting a plain (or PostScript) style hex
dump with xxd -r -p does not depend on the correct number of columns.
Here, anything that looks like a pair of hex digits is interpreted.
Note the difference between
% xxd -i file
and
% xxd -i < file
xxd -s +seek may be different from xxd -s seek, as lseek(2) is used to
"rewind" input. A '+' makes a difference if the input source is stdin,
and if stdin's file position is not at the start of the file by the time
xxd is started and given its input. The following examples may help to
clarify (or further confuse!):
Rewind stdin before reading; needed because the `cat' has already read
to the end of stdin.
% sh -c "cat > plain_copy; xxd -s 0 > hex_copy" < file
Hex dump from file position 0x480 (=1024+128) onwards. The `+' sign
means "relative to the current position", thus the `128' adds to the 1k
where dd left off.
% sh -c "dd of=plain_snippet bs=1k count=1; xxd -s +128 > hex_snippet" <
file
Hex dump from file position 0x100 (=1024-768) onwards.
% sh -c "dd of=plain_snippet bs=1k count=1; xxd -s +-768 > hex_snippet"
< file
However, this is a rare situation and the use of `+' is rarely needed.
The author prefers to monitor the effect of xxd with strace(1) or
truss(1), whenever -s is used.
EXAMPLES
Print everything but the first three lines (hex 0x30 bytes) of file.
% xxd -s 0x30 file
Print 3 lines (hex 0x30 bytes) from the end of file.
% xxd -s -0x30 file
Note: The results of the examples below are relevant to the xxd.1 man
page as of May 2024
Print 120 bytes as a continuous hex dump with 20 octets per line.
% xxd -l 120 -ps -c 20 xxd.1
2e544820585844203120224d6179203230323422
20224d616e75616c207061676520666f72207878
64220a2e5c220a2e5c222032317374204d617920
313939360a2e5c22204d616e2070616765206175
74686f723a0a2e5c2220202020546f6e79204e75
67656e74203c746f6e79407363746e7567656e2e
Hex dump the first 120 bytes of this man page with 12 octets per line.
% xxd -l 120 -c 12 xxd.1
00000000: 2e54 4820 5858 4420 3120 224d .TH XXD 1 "M
0000000c: 6179 2032 3032 3422 2022 4d61 ay 2024" "Ma
00000018: 6e75 616c 2070 6167 6520 666f nual page fo
00000024: 7220 7878 6422 0a2e 5c22 0a2e r xxd"..\"..
00000030: 5c22 2032 3173 7420 4d61 7920 \" 21st May
0000003c: 3139 3936 0a2e 5c22 204d 616e 1996..\" Man
00000048: 2070 6167 6520 6175 7468 6f72 page author
00000054: 3a0a 2e5c 2220 2020 2054 6f6e :..\" Ton
00000060: 7920 4e75 6765 6e74 203c 746f y Nugent <to
0000006c: 6e79 4073 6374 6e75 6765 6e2e ny@sctnugen.
Display just the date from the file xxd.1
% xxd -s 0x33 -l 13 -c 13 xxd.1
00000033: 3231 7374 204d 6179 2031 3939 36 21st May 1996
Copy input_file to output_file and prepend 100 bytes of value 0x00.
% xxd input_file | xxd -r -s 100 > output_file
Patch the date in the file xxd.1
% echo "0000034: 3574 68" | xxd -r - xxd.1
% xxd -s 0x33 -l 13 -c 13 xxd.1
00000033: 3235 7468 204d 6179 2031 3939 36 25th May 1996
Create a 65537 byte file with all bytes 0x00, except for the last one
which is 'A' (hex 0x41).
% echo "010000: 41" | xxd -r > file
Hex dump this file with autoskip.
% xxd -a -c 12 file
00000000: 0000 0000 0000 0000 0000 0000 ............
*
0000fffc: 0000 0000 41 ....A
Create a 1 byte file containing a single 'A' character. The number af-
ter '-r -s' adds to the line numbers found in the file; in effect, the
leading bytes are suppressed.
% echo "010000: 41" | xxd -r -s -0x10000 > file
Use xxd as a filter within an editor such as vim(1) to hex dump a region
marked between `a' and `z'.
:'a,'z!xxd
Use xxd as a filter within an editor such as vim(1) to recover a binary
hex dump marked between `a' and `z'.
:'a,'z!xxd -r
Use xxd as a filter within an editor such as vim(1) to recover one line
of a hex dump. Move the cursor over the line and type:
!!xxd -r
Read single characters from a serial line
% xxd -c1 < /dev/term/b &
% stty < /dev/term/b -echo -opost -isig -icanon min 1
% echo -n foo > /dev/term/b
RETURN VALUES
The following error values are returned:
0 no errors encountered.
-1 operation not supported (xxd -r -i still impossible).
1 error while parsing options.
2 problems with input file.
3 problems with output file.
4,5 desired seek position is unreachable.
SEE ALSO
uuencode(1), uudecode(1), patch(1)
WARNINGS
The tool's weirdness matches its creator's brain. Use entirely at your
own risk. Copy files. Trace it. Become a wizard.
VERSION
This manual page documents xxd version 1.7 from 2024-05.
AUTHOR
(c) 1990-1997 by Juergen Weigert
<jnweiger@informatik.uni-erlangen.de>
Distribute freely and credit me,
make money and share with me,
lose money and don't ask me.
Manual page started by Tony Nugent
<tony@sctnugen.ppp.gu.edu.au> <T.Nugent@sct.gu.edu.au>
Small changes by Bram Moolenaar. Edited by Juergen Weigert.
Manual page for xxd May 2024 XXD(1)
Generated by dwww version 1.16 on Tue Dec 16 04:52:11 CET 2025.