IFCONFIG(8) Linux System Administrator's Manual IFCONFIG(8)
NAME
ifconfig - configure a network interface
SYNOPSIS
ifconfig [-v] [-a] [-s] [interface]
ifconfig [-v] interface [aftype] options | address ...
DESCRIPTION
Ifconfig is used to configure the kernel-resident network interfaces.
It is used at boot time to set up interfaces as necessary. After that,
it is usually only needed when debugging or when system tuning is
needed.
If no arguments are given, ifconfig displays the status of the currently
active interfaces. If a single interface argument is given, it displays
the status of the given interface only; if a single -a argument is
given, it displays the status of all interfaces, even those that are
down. Otherwise, it configures an interface.
Address Families
If the first argument after the interface name is recognized as the name
of a supported address family, that address family is used for decoding
and displaying all protocol addresses. Currently supported address fam-
ilies include inet (TCP/IP, default), inet6 (IPv6), ax25 (AMPR Packet
Radio), ddp (Appletalk Phase 2), ipx (Novell IPX) and netrom (AMPR
Packet radio). All numbers supplied as parts in IPv4 dotted decimal no-
tation may be decimal, octal, or hexadecimal, as specified in the ISO C
standard (that is, a leading 0x or 0X implies hexadecimal; otherwise, a
leading '0' implies octal; otherwise, the number is interpreted as deci-
mal). Use of hexadecimal and octal numbers is not RFC-compliant and
therefore its use is discouraged.
OPTIONS
-a display all interfaces which are currently available, even if
down
-s display a short list (like netstat -i)
-v be more verbose for some error conditions
interface
The name of the interface. This is usually a driver name fol-
lowed by a unit number, for example eth0 for the first Ethernet
interface. If your kernel supports alias interfaces, you can
specify them with syntax like eth0:0 for the first alias of eth0.
You can use them to assign more addresses. To delete an alias in-
terface use ifconfig eth0:0 down. Note: for every scope (i.e.
same net with address/netmask combination) all aliases are
deleted, if you delete the first (primary).
up This flag causes the interface to be activated. It is implicitly
specified if an address is assigned to the interface; you can
suppress this behavior when using an alias interface by appending
an - to the alias (e.g. eth0:0-). It is also suppressed when
using the IPv4 0.0.0.0 address as the kernel will use this to im-
plicitly delete alias interfaces.
down This flag causes the driver for this interface to be shut down.
[-]arp Enable or disable the use of the ARP protocol on this interface.
[-]promisc
Enable or disable the promiscuous mode of the interface. If se-
lected, all packets on the network will be received by the inter-
face.
[-]allmulti
Enable or disable all-multicast mode. If selected, all multicast
packets on the network will be received by the interface.
mtu N This parameter sets the Maximum Transfer Unit (MTU) of an inter-
face.
dstaddr addr
Set the remote IP address for a point-to-point link (such as
PPP). This keyword is now obsolete; use the pointopoint keyword
instead.
netmask addr
Set the IP network mask for this interface. This value defaults
to the usual class A, B or C network mask (as derived from the
interface IP address), but it can be set to any value.
add addr/prefixlen
Add an IPv6 address to an interface.
del addr/prefixlen
Remove an IPv6 address from an interface.
tunnel ::aa.bb.cc.dd
Create a new SIT (IPv6-in-IPv4) device, tunnelling to the given
destination.
irq addr
Set the interrupt line used by this device. Not all devices can
dynamically change their IRQ setting.
io_addr addr
Set the start address in I/O space for this device.
mem_start addr
Set the start address for shared memory used by this device.
Only a few devices need this.
media type
Set the physical port or medium type to be used by the device.
Not all devices can change this setting, and those that can vary
in what values they support. Typical values for type are 10base2
(thin Ethernet), 10baseT (twisted-pair 10Mbps Ethernet), AUI (ex-
ternal transceiver) and so on. The special medium type of auto
can be used to tell the driver to auto-sense the media. Again,
not all drivers can do this.
[-]broadcast [addr]
If the address argument is given, set the protocol broadcast ad-
dress for this interface. Otherwise, set (or clear) the
IFF_BROADCAST flag for the interface.
[-]pointopoint [addr]
This keyword enables the point-to-point mode of an interface,
meaning that it is a direct link between two machines with nobody
else listening on it.
If the address argument is also given, set the protocol address
of the other side of the link, just like the obsolete dstaddr
keyword does. Otherwise, set or clear the IFF_POINTOPOINT flag
for the interface.
hw class address
Set the hardware address of this interface, if the device driver
supports this operation. The keyword must be followed by the
name of the hardware class and the printable ASCII equivalent of
the hardware address. Hardware classes currently supported in-
clude ether (Ethernet), ax25 (AMPR AX.25), ARCnet and netrom
(AMPR NET/ROM).
multicast
Set the multicast flag on the interface. This should not normally
be needed as the drivers set the flag correctly themselves.
address
The IP address to be assigned to this interface.
txqueuelen length
Set the length of the transmit queue of the device. It is useful
to set this to small values for slower devices with a high la-
tency (modem links, ISDN) to prevent fast bulk transfers from
disturbing interactive traffic like telnet too much.
name newname
Change the name of this interface to newname. The interface must
be shut down first.
NOTES
Since kernel release 2.2 there are no explicit interface statistics for
alias interfaces anymore. The statistics printed for the original ad-
dress are shared with all alias addresses on the same device. If you
want per-address statistics you should add explicit accounting rules for
the address using the iptables(8) command.
Since net-tools 1.60-4 ifconfig is printing byte counters and human
readable counters with IEC 60027-2 units. So 1 KiB are 2^10 byte. Note,
the numbers are truncated to one decimal (which can by quite a large er-
ror if you consider 0.1 PiB is 112.589.990.684.262 bytes :)
Interrupt problems with Ethernet device drivers fail with EAGAIN (SIOC-
SIIFLAGS: Resource temporarily unavailable) it is most likely a inter-
rupt conflict. See http://www.scyld.com/expert/irq-conflict.html for
more information.
FILES
/proc/net/dev
/proc/net/if_inet6
BUGS
Ifconfig uses the ioctl access method to get the full address informa-
tion, which limits hardware addresses to 8 bytes. Because Infiniband
hardware address has 20 bytes, only the first 8 bytes are displayed cor-
rectly. Please use ip link command from iproute2 package to display
link layer informations including the hardware address.
While appletalk DDP and IPX addresses will be displayed they cannot be
altered by this command.
SEE ALSO
route(8), netstat(8), arp(8), rarp(8), iptables(8), ifup(8), inter-
faces(5)
http://physics.nist.gov/cuu/Units/binary.html - Prefixes for binary mul-
tiples
AUTHORS
Fred N. van Kempen, <waltje@uwalt.nl.mugnet.org>
Alan Cox, <Alan.Cox@linux.org>
Phil Blundell, <Philip.Blundell@pobox.com>
Andi Kleen
Bernd Eckenfels, <net-tools@lina.inka.de>
net-tools 2008-10-03 IFCONFIG(8)
Generated by dwww version 1.16 on Thu Mar 19 15:45:52 CET 2026.