TIOCLINUX(2const) TIOCLINUX(2const)
NAME
TIOCLINUX - ioctls for console terminal and virtual consoles
SYNOPSIS
#include <linux/tiocl.h> /* Definition of TIOCL_* constants */
#include <sys/ioctl.h>
int ioctl(int fd, TIOCLINUX, void *argp);
DESCRIPTION
The action of the following ioctls depends on the first byte in the
struct pointed to by argp, referred to here as the subcode. These are
legal only for the superuser or the owner of the current terminal.
subcode=0
Dump the screen. Disappeared in Linux 1.1.92. (With Linux
1.1.92 or later, read from /dev/vcsN or /dev/vcsaN instead.)
subcode=1
Get task information. Disappeared in Linux 1.1.92.
subcode=TIOCL_SETSEL
Set selection. argp points to a
struct {
char subcode;
short xs, ys, xe, ye;
short sel_mode;
};
xs and ys are the starting column and row. xe and ye are the
ending column and row. (Upper left corner is row=column=1.)
sel_mode is 0 for character-by-character selection, 1 for word-
by-word selection, or 2 for line-by-line selection. The indi-
cated screen characters are highlighted and saved in a kernel
buffer.
Since Linux 6.7, using this subcode requires the CAP_SYS_ADMIN
capability.
subcode=TIOCL_PASTESEL
Paste selection. The characters in the selection buffer are
written to fd.
Since Linux 6.7, using this subcode requires the CAP_SYS_ADMIN
capability.
subcode=TIOCL_UNBLANKSCREEN
Unblank the screen.
subcode=TIOCL_SELLOADLUT
Sets contents of a 256-bit look up table defining characters in a
"word", for word-by-word selection. (Since Linux 1.1.32.)
Since Linux 6.7, using this subcode requires the CAP_SYS_ADMIN
capability.
subcode=TIOCL_GETSHIFTSTATE
argp points to a char which is set to the value of the kernel
variable shift_state. (Since Linux 1.1.32.)
subcode=TIOCL_GETMOUSEREPORTING
argp points to a char which is set to the value of the kernel
variable report_mouse. (Since Linux 1.1.33.)
subcode=8
Dump screen width and height, cursor position, and all the char-
acter-attribute pairs. (Linux 1.1.67 through Linux 1.1.91 only.
With Linux 1.1.92 or later, read from /dev/vcsa* instead.)
subcode=9
Restore screen width and height, cursor position, and all the
character-attribute pairs. (Linux 1.1.67 through Linux 1.1.91
only. With Linux 1.1.92 or later, write to /dev/vcsa* instead.)
subcode=TIOCL_SETVESABLANK
Handles the Power Saving feature of the new generation of moni-
tors. VESA screen blanking mode is set to argp[1], which governs
what screen blanking does:
0 Screen blanking is disabled.
1 The current video adapter register settings are saved,
then the controller is programmed to turn off the vertical
synchronization pulses. This puts the monitor into
"standby" mode. If your monitor has an Off_Mode timer,
then it will eventually power down by itself.
2 The current settings are saved, then both the vertical and
horizontal synchronization pulses are turned off. This
puts the monitor into "off" mode. If your monitor has no
Off_Mode timer, or if you want your monitor to power down
immediately when the blank_timer times out, then you
choose this option. (Caution: Powering down frequently
will damage the monitor.) (Since Linux 1.1.76.)
subcode=TIOCL_SETKMSGREDIRECT
Change target of kernel messages ("console"): by default, and if
this is set to 0, messages are written to the currently active
VT. The VT to write to is a single byte following subcode.
(Since Linux 2.5.36.)
subcode=TIOCL_GETFGCONSOLE
Returns the number of VT currently in foreground. (Since Linux
2.5.36.)
subcode=TIOCL_SCROLLCONSOLE
Scroll the foreground VT by the specified amount of lines down,
or half the screen if 0. lines is *(((int32_t *)&subcode) + 1).
(Since Linux 2.5.67.)
subcode=TIOCL_BLANKSCREEN
Blank the foreground VT, ignoring "pokes" (typing): can only be
unblanked explicitly (by switching VTs, to text mode, etc.).
(Since Linux 2.5.71.)
subcode=TIOCL_BLANKEDSCREEN
Returns the number of VT currently blanked, 0 if none. (Since
Linux 2.5.71.)
subcode=16
Never used.
subcode=TIOCL_GETKMSGREDIRECT
Returns target of kernel messages. (Since Linux 2.6.17.)
RETURN VALUE
On success, 0 is returned (except where indicated). On failure, -1 is
returned, and errno is set to indicate the error.
ERRORS
EINVAL argp is invalid.
EPERM Insufficient permission.
STANDARDS
Linux.
SEE ALSO
ioctl(2), ioctl_console(2)
Linux man-pages 6.9.1 2024-06-13 TIOCLINUX(2const)
Generated by dwww version 1.16 on Tue Dec 16 03:56:37 CET 2025.